Nissan Murano: Warning Chime System :: Symptom Diagnosis / The Seat Belt Warning Continues Sounding, or Does Not Sound
-
Seat belt warning does not sound even though driver seat belt is not fastened.
-
Seat belt warning sounds even though driver seat belt is fastened.
CHECK WARNING CHIME OPERATION
CONSULT
-
Select “SEAT BELT WARN TEST” in “Active Test” mode of “BCM(BUZZER)".
-
Select “ON/OFF” to check that the function operates normally.
| Component | CONSULT | Condition |
| Buzzer | SEAT BELT WARN TEST | ON |
| OFF |
Is the inspection result normal?
YES>>GO TO 2.
NO>>Replace combination meter. Refer to Removal and Installation.
CHECK COMBINATION METER INPUT SIGNAL
Check the combination meter input signal. Refer to Component Function Check.
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>GO TO 3.
CHECK FRONT SEAT BELT BUCKLE SWITCH LH CIRCUIT
Check the front seat belt buckle switch LH circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace harness or connector.
CHECK FRONT SEAT BELT BUCKLE SWITCH LH
Check the front seat belt buckle switch LH. Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace the combination meter. Refer to Removal and Installation.
NO>>Replace the front seat belt buckle switch LH. Refer to Removal and Installation.
The Light Reminder Warning Does Not Sound
Diagnosis Procedure
Light reminder warning does not sound even though headlamp is illuminated.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (lighting switch)...
The Parking Brake Release Warning Continues Sounding, or Does Not Sound
Diagnosis Procedure
The parking brake warning buzzer sounds continuously during vehicle travel, even though the parking brake is released.
The parking brake warning buzzer does not sound at all, even while driving the Nissan Murano vehicle with the parking brake applied...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: C1a34-64 Command Error
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition C1A34–64 COMMAND ERROR (Command error) Diagnosis condition When MAIN switch of ICC system is ON When driving the Nissan Murano vehicle Signal (terminal) CAN communication signal Threshold If an error occurs in the command signal that ADAS control unit transmits to ECM via CAN communication Diagnosis delay time 1 second or less POSSIBLE CAUSEADAS control unitFAIL-SAFEThe following systems are canceled: Vehicle-to-vehicle distance control mode Conventional (fixed speed) cruise control mode Automatic Emergency Braking (AEB) Automatic Emergency Braking (AEB) with pedestrian detection Intelligent Forward Collision Warning (I-FCW) Confirmation Procedure CHECK DTC PRIORITY If DTC “C1A34–64” is displayed with DTC “U1000–01”, first diagnose the DTC “U1000–01”...
Nissan Murano (Z52) 2015-2024 Service Manual: Telescopic Sensor
Component Function Check DATA MONITOR CONSULT Select “TELESCO PULSE” in “Data Monitor” mode of “AUTO DRIVE POS.”. Check that the function operates normally according to the following conditions: Monitor item Condition Value TELESCO PULSE Steering column Operate (forward) Change (decrease) Operate (backward) Change (increase) Release No change Is the inspection result normal? YES>> Inspection End...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Settings
- High Beam Assist (if so equipped)
- Shift lock release
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
