Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / Seat Memory Indicator
ACTIVE TEST
CONSULT
-
Select “MEMORY SW INDCTR” in “Active Test” mode of “AUTO DRIVE POS.”.
-
Check that the function operates normally.
| Test item | Description | ||
|---|---|---|---|
| MEMORY SW INDCTR | Off | Memory switch indicator | Off |
| ON-1 | Indicator 1: ON | ||
| ON-2 | Indicator 2: ON | ||
Is the operation of relevant parts normal?
YES>>Inspection End.
NO>>Perform diagnosis procedure. Refer to Diagnosis Procedure.
CHECK SEAT MEMORY INDICATOR CIRCUIT
-
Ignition switch OFF.
-
Disconnect driver seat control unit and seat memory switch.
-
Check continuity between driver seat control unit harness connector and seat memory switch harness connector.
Driver seat control unit Seat memory switch Continuity Connector Terminal Connector Terminal B209 10 D51 4 Yes 26 5 -
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit Ground Continuity Connector Terminal B209 10 No 26
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace harness.
CHECK MEMORY INDICATOR POWER SUPPLY
Check voltage between seat memory switch harness connector and ground.
| (+) | (–) |
Voltage (Approx.) | |
|---|---|---|---|
| Seat memory switch | |||
| Connector | Terminal | ||
| D51 | 7 | Ground | Battery voltage |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Check the following:
-
10A fuse No. 9.
-
Harness for open or short between memory indicator and fuse.
CHECK MEMORY INDICATOR
Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace seat memory switch. Refer to Removal and Installation.
CHECK INTERMITTENT INCIDENT
Refer to Intermittent Incident.
Is the inspection result normal?
YES>>Replace driver seat control unit. Refer to Removal and Installation.
NO>>Repair or replace the malfunctioning part.
CHECK SEAT MEMORY INDICATOR
-
Ignition switch OFF.
-
Disconnect seat memory switch.
-
Check continuity between seat memory switch terminals.
Seat memory switch Continuity Terminal (+) (-) 7 4 Yes 5
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace seat memory switch. Refer to Removal and Installation.
Door Mirror Motor
Component Function Check
ACTIVE TEST
CONSULT
Select “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “Active Test” mode of “AUTO DRIVE POS.”...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Low Tire Pressure Warning Lamp Blinks
Diagnosis Procedure When the ignition switch is placed ON, the low tire pressure warning lamp blinks. And then 1 minute later, low tire pressure warning lamp turns ON.NOTE: The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire pressure warning lamp...
Nissan Murano (Z52) 2015-2024 Service Manual: Half Switch
Component Function Check CHECK FUNCTION CONSULT Select “HALF LATCH SW” in “Data Monitor” mode of “AUTO BACK DOOR”. Check that the function operates normally according to the following conditions: Monitor Item Condition Status HALF LATCH SW Back door Open/fully closed OFF Half latch ON Is the inspection result normal? YES>> Half latch switch is OK...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Warning lights
- How to enable/disable the LDW system
- GAS STATION INFORMATION
- New on site
- Most important about car
Vehicle security system
Your vehicle has two types of security systems:
Vehicle security system NISSAN Vehicle Immobilizer SystemThe vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
