Nissan Murano: Security Control System :: Dtc/circuit Diagnosis / P1612 Chain of Ecm-Immu
DTC DETECTION LOGIC
NOTE:
-
If DTC P1612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description.
-
If DTC P1612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to DTC Description.
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC Detection Condition | |
|---|---|---|---|
| P1612 |
CHAIN OF ECM-IMMU (Chain of engine control module - immobilizer unit) |
Diagnosis condition | When ignition switch ON. |
| Signal (terminal) | — | ||
| Threshold | Inactive communication between BCM and ECM | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
ECM
-
Harness or connector
(The CAN communication line is open or shorted.)
-
BCM
FAIL-SAFE
—
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “ENGINE”.
-
Check DTC.
Is DTC detected?
YES>>Refer to Diagnosis Procedure.
NO>>Inspection End.
NOTE:
-
If DTC P1612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description.
-
If DTC P1612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to DTC Description.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT.
Check BCM power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the harness.
CHECK ECM POWER SUPPLY AND GROUND CIRCUIT.
Check ECM power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the harness.
PERFORM DTC CONFIRMATION PROCEDURE.
Perform the DTC confirmation procedure. Refer to DTC Confirmation Procedure.
Does the DTC return?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Inspection End.
P1611 Id Discord, Immu-Ecm
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
P1611
ID DISCORD, IMMU-ECM
(Identification discord immobilizer-engine control unit)
Diagnosis condition
When ignition switch ON...
P1614 Chain of Immu-Key
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
P1614
CHAIN OF IMMU-KEY
(Chain of immobilizer-key)
Diagnosis condition
When ignition switch ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Interior Room Lamp Control Circuit
Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Battery saver output/power supply circuit Front room/map lamp assembly Personal lamps 2nd row CHECK INTERIOR ROOM LAMP CONTROL FUNCTION CONSULT Set the front room/map lamp assembly switch and personal lamps 2nd row switch to DOOR: Ignition switch ON...
Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis and Repair Work Flow
Work Flow OVERALL SEQUENCEDETAILED FLOWGET INFORMATION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). At the dealer, check whether the customer’s Nissan Murano vehicle has been registered for the telematics service...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Vehicle Dynamic Control (VDC) OFF switch
- Warning lights
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
