Nissan Murano: Steering Control System :: Dtc/circuit Diagnosis / Hydraulic Pump Electric Power Steering Warning Lamp
CHECK THE ILLUMINATION OF THE HYDRAULIC PUMP ELECTRIC POWER STEERING WARNING LAMP
Check that the hydraulic pump electric power steering warning lamp turns ON when ignition switch ON. Then, hydraulic pump electric power steering warning lamp turns OFF after the engine is started.
Is the inspection result normal?
YES>>Inspection End.
NO>>Perform trouble diagnosis. Refer to Diagnosis Procedure.
SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch OFF to ON.
-
Select "Self Diagnostic Result" mode of "EPS/DAST 3".
Is any DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK HYDRAULIC PUMP ELECTRIC POWER STEERING WARNING LAMP SIGNAL
CONSULT
-
Ignition switch ON.
-
Select "WARNING LAMP" in "Data Monitor" mode of "EPS/DAST 3".
-
Check that the item in “Data Monitor” mode is “On”.
CAUTION:
Engine should not be running for step 3.
-
Start the engine.
CAUTION:
Never drive the Nissan Murano vehicle during the test.
-
Check that the item in “Data Monitor” mode is “Off”.
Is the inspection result normal?
YES>>Perform the trouble diagnosis for combination meter power supply circuit. Refer to Diagnosis Procedure.
NO>>GO TO 3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check the power steering control module pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>Power steering control module is malfunctioning. Replace power steering oil pump assembly. Refer to Removal and Installation.
NO>>Repair or replace the malfunctioning component.
U1000 Can Comm Circuit
DTC Description
DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real-time application. It is an on-Nissan Murano vehicle multiplex communication line with high data communication speed and excellent error detection ability...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Seat Belt Warning
Seat Belt Warning Chime SYSTEM DIAGRAMWARNING OPERATION CONDITIONSFront Seat BeltsIf all of the following conditions are fulfilled: Operation conditions Ignition switch ON Nissan Murano Vehicle speed Approximately 9.3 mph (15 km/h) or more. Front seat belt buckle switch LH Unfastened (front seat belt buckle switch LH ON) Front seat belt buckle switch RH Front passenger seat is occupied, seat belt unfastened (front seat belt buckle switch RH ON)...
Nissan Murano (Z52) 2015-2024 Service Manual: Front Axle :: Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
NVH Troubleshooting Chart Use chart below to find the cause of the symptom. If necessary, repair or replace these parts. Reference — Inspection — Exploded View — Inspection NVH Troubleshooting Chart Inspection NVH Troubleshooting Chart NVH Troubleshooting Chart Inspection NVH Troubleshooting Chart NVH Troubleshooting Chart Possible cause and SUSPECTED PARTS Excessive joint angle Joint sliding resistance Imbalance Improper installation, looseness Parts interference Wheel bearing damage FRONT SUSPENSION FRONT AXLE TIRE WHEEL DRIVE SHAFT BRAKE STEERING Symptom DRIVE SHAFT Noise × × - - - × × × × × - × × Shake × - × - - × × × × × - × × FRONT AXLE Noise - - - × × × × × × × × × Shake - - - × × × × × × × × × Vibration - - - × × × × - × - × - × Shimmy - - - × × - × - × × - × × Shudder - - - × - × - × × - × × Poor quality ride or handling - - - × × - × - × × - - - Inspect Front Axle for cracks or damage...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Vehicle Dynamic Control (VDC) OFF switch
- Power Steering Fluid (PSF)
- All-Wheel Drive (AWD) (if so equipped)
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
