Nissan Murano: Door & Lock :: Dtc/circuit Diagnosis / Half Switch

Nissan Murano (Z52) 2015-2024 Service Manual / Body Exterior, Doors, Roof & Vehicle Security / Door & Lock :: Dtc/circuit Diagnosis / Half Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Select “HALF LATCH SW” in “Data Monitor” mode of “AUTO BACK DOOR”.

  2. Check that the function operates normally according to the following conditions:

Monitor Item Condition Status
HALF LATCH SW Back door Open/fully closed OFF
Half latch ON

Is the inspection result normal?

YES>>

Half latch switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HALF LATCH SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect back door lock assembly connector.

  3. Check voltage between back door lock assembly harness connector and ground.

    (–) (–)

    Voltage

    (Approx.)
    Back door lock assembly
    Connector Terminal
    D557 6 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK HALF LATCH SWITCH CIRCUIT

  1. Disconnect automatic back door control module connector.

  2. Check continuity between automatic back door control module harness connector and back door lock assembly harness connector.

    Automatic back door control module Back door lock assembly Continuity
    Connector Terminal Connector Terminal
    B55 3 D557 6 Yes

  3. Check continuity between automatic back door control module harness connector and ground.

    Automatic back door control module Ground Continuity
    Connector Terminal
    B55 3 No

Is the inspection result normal?

YES>>

Replace automatic back door control module. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HALF LATCH SWITCH GROUND CIRCUIT

  1. Check continuity between back door lock assembly harness connector and ground.

    Back door lock assembly Ground Continuity
    Connector Terminal
    D557 8 No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK HALF LATCH SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace back door lock assembly. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK HALF LATCH SWITCH

  1. Ignition switch OFF.

  2. Disconnect back door lock assembly connector.

  3. Check continuity between back door lock assembly terminals.

Back door lock assembly Condition Continuity
Terminal
6 8 Back door Open Yes
Fully closed/Half latch No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace back door lock assembly. Refer to Removal and Installation.

    Key Warning Lamp

    Component Function Check CHECK FUNCTION CONSULT Select “INDICATOR” in “Active Test” mode of “BCM(INTELLIGENT KEY)”. Select “KEY IND” or “KEY ON” to check that it works normally...

    Touch Sensor. Rh

    Component Function Check CHECK FUNCTION CONSULT Select “TOUCH SEN RH” in “Data Monitor” mode of “AUTO BACK DOOR”. Check that the function operates normally according to the following conditions: Monitor Item Condition Status TOUCH SEN RH Touch sensor RH Other than below OFF Detect obstruction ON Is the inspection result normal? YES>> Touch sensor RH is OK...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Glass & Window System :: Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses


    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any customer's comments; refer to Diagnostic Worksheet...

    Nissan Murano (Z52) 2015-2024 Service Manual: Internal Heat Exchanger


    Removal and Installation REMOVALDischarge the refrigerant. Refer to Recycle Refrigerant. Remove the engine room cover. Refer to Removal and Installation. Remove the torque member bolts. Refer to Exploded View. Position the brake caliper assembly aside using wire...

    Categories

    Fuel gauge

    Nissan Murano. Fuel gauge

    The gauge indicates the approximate fuel level in the tank.

    The gauge may move slightly during braking, turning, acceleration, or going up or down hills.

    The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.

    read more

     
    Copyright © 2026 www.nimurano.com