Nissan Murano: Road Wheels & Tires :: Symptom Diagnosis / Easy Fill Tire Alert Does Not Activate
The Easy Fill tire alert does not function while inflating a tire when the select lever position is in P-range with the ignition switch is placed ON.
NOTE:
-
After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function.
-
If there is no response for approximately 15 seconds or more after inflating the tires, cancel the use of the Easy Fill tire alert function or move the Nissan Murano vehicle approximately 3.2 ft. (1 m) backward or forward to try again. The air filler pressure may be weak or out of service area.
-
For Easy Fill tire alert, Refer to Easy Fill Tire Alert Function.
LOCATION CHANGE
Move the vehicle to another area and repeat the procedure of the Easy fill tire alert function. Refer to Easy Fill Tire Alert Function.
Is the function normal?
YES>>Inspection End.
NO>>GO TO 2.
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Are any DTCs detected?
YES>>Refer to DTC Index.
NO>>GO TO 3.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Do the hazard warning lamps operate?
YES>>GO TO 4.
NO>>Refer to Diagnosis Procedure.
PERFORM SELF DIAGNOSTIC RESULT FOR TCM
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “TRANSMISSION”.
-
Check DTC.
Are any DTCs detected?
YES>>Refer to Diagnosis Description.
NO>>GO TO 5.
CHECK HORN OPERATION
Check horn operation. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace malfunctioning components.
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Drive at a speed of 25 MPH (40 km/h) or more for 3 minutes, and then drive the Nissan Murano vehicle at any speed for 10 minutes.
-
Select “Self Diagnostic Result” mode of “BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Are any DTCs detected?
YES>>Refer to DTC Index.
NO>>Replace BCM. Refer to Removal and Installation.
Low Tire Pressure Warning Lamp Blinks
Diagnosis Procedure
When the ignition switch is placed ON, the low tire pressure warning lamp blinks. And then 1 minute later, low tire pressure warning lamp turns ON...
Id Registration Cannot Be Completed
Diagnosis Procedure
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Front Camera Unit
Values on the Diagnosis Tool VALUE ON THE DIAGNOSIS TOOLNOTE: The following table includes information (items) inapplicable to this Nissan Murano vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor item Condition Value/Status CAMERA HIGH TEMP When the temperature around lane camera unit is adequate NORMAL When the temperate around the lane camera unit is high HIGH WIPER Ignition switch ON Wiper position is High Hi Wiper position is Low Lo Wiper position is OFF Off TURN SIGNAL Turn signal lamp LH and RH blinking LH&RH Turn signal lamp LH blinking LH Turn signal lamp RH blinking RH Turn signal lamps OFF Off Nissan Murano Vehicle SPEED While drive km/h DRIVER ASSIST SYSTEM SET NOTE: The item is displayed, but it is not used...
Nissan Murano (Z52) 2015-2024 Service Manual: C1a34-64 Command Error
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition C1A34–64 COMMAND ERROR (Command error) Diagnosis condition When MAIN switch of ICC system is ON When driving the Nissan Murano vehicle Signal (terminal) CAN communication signal Threshold If an error occurs in the command signal that ADAS control unit transmits to ECM via CAN communication Diagnosis delay time 1 second or less POSSIBLE CAUSEADAS control unitFAIL-SAFEThe following systems are canceled: Vehicle-to-vehicle distance control mode Conventional (fixed speed) cruise control mode Automatic Emergency Braking (AEB) Automatic Emergency Braking (AEB) with pedestrian detection Intelligent Forward Collision Warning (I-FCW) Confirmation Procedure CHECK DTC PRIORITY If DTC “C1A34–64” is displayed with DTC “U1000–01”, first diagnose the DTC “U1000–01”...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Vehicle Dynamic Control (VDC) OFF switch
- Settings
- Fuel recommendation
- New on site
- Most important about car
Unfastening the seat belts. Checking seat belt operation
Unfastening the seat belts
To unfasten the seat belt, press the button
on the buckle 
. The seat belt
automatically
retracts.
