Nissan Murano: Door & Lock :: System Description / Diagnosis System (automatic Back Door Control Module)

Nissan Murano (Z52) 2015-2024 Service Manual / Body Exterior, Doors, Roof & Vehicle Security / Door & Lock :: System Description / Diagnosis System (automatic Back Door Control Module)

CONSULT Function (AUTO BACK DOOR)

APPLICATION ITEMS

CONSULT performs the following functions via CAN communication with automatic back door control module:

Diagnosis mode	Function Description
Self diagnostic result	Displays the diagnosis results judged by automatic back door control module.
Data monitor	The automatic back door control module input/output signals are displayed.
Work support	Changes the setting for each setting function.
ECU identification	The automatic back door control module part number is displayed.
CAN Diag Support Mntr	The result of transmit/receive diagnosis of CAN communication is displayed.

SELF DIAGNOSTIC RESULTS

Refer to DTC Index.

DATA MONITOR

Monitor Item	Unit	Description
SPINDLE SENSOR LH	[Pulse]	Displays the condition of the LH encoder.
SPINDLE LH SPEED	[mm/s]	Displays the LH spindle operation speed.
SPINDLE MOTOR LH DUTY	[%]	Displays the condition of the spindle motor LH duty.
VHCL SPEED MTR	[km/h]	Displays the Nissan Murano vehicle speed signal received from combination meter as a numerical value.
VHCL SPEED ABS	[km/h]	Displays the Nissan Murano vehicle speed signal received from ABS actuator and electrical unit as a numerical value.
MAIN SW	[ON/OFF]	Indicates condition of automatic back door main switch.
AUTO BD SW	[ON/OFF]	Indicates condition of automatic back door switch.
BK DOOR CL SW	[ON/OFF]	Indicates condition of automatic back door close switch.
BACK DOOR LOCK STATUS	[ON/OFF]	Indicates condition of back door lock status.
PKB SW	[ON/OFF]	Indicates condition of parking brake switch.
OPEN SW	[ON/OFF]	Indicates condition of open switch.
CLOSE SW	[ON/OFF]	Indicates condition of close switch.
HALF LATCH SW	[ON/OFF]	Indicates condition of half latch switch.
TOUCH SEN RH	[ON/OFF/OPEN]	Indicates condition of touch sensor RH.
TOUCH SEN LH	[ON/OFF/OPEN]	Indicates condition of touch sensor LH.
P RANGE IND	[ON/OFF]	Indicates condition of P range signal from combination meter.
RKE REQ	[OFF/MOVE/REV]	Indicates condition of remote keyless entry signal from BCM.
IGN SW	[ON/OFF]	Indicates condition of IGN power supply.
SPINDLE LH ENCODER A	[LO/HI]	Indicates condition of encoder signal from encoder A.
SPINDLE LH ENCODER B	[LO/HI]	Indicates condition of encoder signal from encoder B.
DESTINATION	[JPN/NAM]	Indicates specification of destination of the automatic back door system.
AUTO BCK DR POS INITIAL	[YET/DONE]	Indicates condition of calibration of automatic back door position information.
AUTO BCK DR POS LEARN	[YET/DONE]	Indicates condition of additional service when removing battery negative cable.
SPINDLE SENSOR RH	[Pulse]	Displays the condition of the RH encoder.
SPINDLE RH SPEED	[mm/s]	Displays the RH spindle operation speed.
SPINDLE MOTOR RH DUTY	[%]	Displays the condition of the spindle motor RH duty.
SPINDLE RH ENCODER A	[LO/HI]	Indicates condition of encoder signal from encoder A.
SPINDLE RH ENCODER B	[LO/HI]	Indicates condition of encoder signal from encoder B.
TRANSMISSION TYPE	[AT/CVT]	Indicates type of transmission the Nissan Murano vehicle is equipped with.

WORK SUPPORT

Work item	Description	Refer to
RESET AUTO BACK DOOR STATUS	This item is for calibration of automatic back door position information.	Work Procedure

System (integrated Homelink Transceiver)

System Description Item Function Integrated HomeLink® transceiver A maximum of 3 radio signals can be stored and transmitted to operate the garage door, etc...

Door & Lock :: Ecu Diagnosis Information

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Abs Warning Lamp

Component Function Check CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for 1 second after ignition switch ON. CAUTION: Never start the engine. Is the inspection result normal? YES>> Inspection End. NO>> Proceed to Diagnosis Procedure...

Nissan Murano (Z52) 2015-2024 Service Manual: P219a Air Fuel Ratio

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P219A AIR FUEL RATIO IMBALANCE B1 (Air-fuel ratio imbalance bank 1) Diagnosis condition — Signal (terminal) — Threshold ECM detects a lean/rich air fuel ratio state in any cylinder for a specified length of time Diagnosis delay time — P219B AIR FUEL RATIO IMBALANCE B2 (Air-fuel ratio imbalance bank 2) Diagnosis condition — Signal (terminal) — Threshold ECM detects a lean/rich air fuel ratio state in any cylinder for a specified length of time Diagnosis delay time — POSSIBLE CAUSEDTC P219A Fuel injector Exhaust gas leaks Incorrect fuel pressure Mass air flow sensor Intake air leaks Lack of fuel Incorrect PCV hose connection Improper spark plug Insufficient compression The fuel injector circuit is open or shorted Ignition coil The ignition signal circuit is open or shorted DTC P219B Fuel injector Exhaust gas leaks Incorrect fuel pressure Mass air flow sensor Intake air leaks Lack of fuel Incorrect PCV hose connection Improper spark plug Insufficient compression The fuel injector circuit is open or shorted Ignition coil The ignition signal circuit is open or shorted FAIL-SAFENot applicable DTC Confirmation Procedure CHECK DTC PRIORITY If DTC P219A or P219B is displayed with other DTC, first perform the trouble diagnosis for the other DTC...