Nissan Murano: Dtc/circuit Diagnosis / C1a21 Unit High Temp
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |
|---|---|---|---|
| C1A21–48 |
UNIT HIGH TEMP (Unit high temperature) |
Diagnosis condition | When Ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | Temperature around distance sensor (ICC sensor) is high. | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
Temperature around the distance sensor (ICC sensor) becomes extremely high.
FAIL-SAFE
The following systems are canceled:
-
Intelligent Cruise Control
-
Automatic Emergency Braking (AEB)
-
Intelligent Forward Collision Warning (I-FCW)
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Turn the ignition switch OFF.
-
Wait for 10 minutes or more.
-
Start the engine.
-
Turn the MAIN switch of ICC system ON.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the “C1A21–48” is detected as the current malfunction in “Self Diagnostic Result” mode of “LASER/RADAR”.
Is “C1A21–48” detected as the current malfunction?
YES>>Refer to Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CHECK ENGINE COOLING SYSTEM
Check for any malfunctions in engine cooling system.
Is engine cooling system normal?
YES>>Replace the distance sensor (ICC sensor). Refer to Removal and Installation.
NO>>Repair engine cooling system.
C1a18 Radar Aiming Incmp
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition
C1A18–54
LASER AIMING INCMP
Diagnosis condition
When Ignition switch is ON...
C1a23 Unit Low Temp
DTC Description
DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detecting condition
C1A23
(97)
UNIT LOW TEMP
Temperature detected by the temperature sensor integrated in distance sensor (ICC sensor) remains less than -40 °C for 5 seconds or more
POSSIBLE CAUSETemperature around the distance sensor (ICC sensor) becomes extremely lowFAIL-SAFEThe following systems are canceled...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: C1201 Controller Failure
DTC Description DTC DETECTION LOGICMalfunction has occurred inside AWD control unit. DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1201 CONTROLLER FAILURE (Control unit failure) Diagnosis condition Ignition switch: ON Signal — Threshold — Diagnosis delay time — POSSIBLE CAUSEInternal malfunction of AWD control unitFAIL-SAFEFront-wheel drive or shifts to 4-wheel drive (rear-wheels still have some driving torque)...
Nissan Murano (Z52) 2015-2024 Service Manual: U1010 Control Unit(can)
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1010 CONTROL UNIT(CAN) [Control unit(CAN)] Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold — Diagnosis delay time — POSSIBLE CAUSEAround view monitor control unitFAIL-SAFE— DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Vehicle Dynamic Control (VDC) OFF switch
- Turning the AEB system on/off
- Indicator lights
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
