Nissan Murano: Dtc/circuit Diagnosis / C1a01 Power Supply Circuit 1
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |
|---|---|---|---|
| C1A01–16 |
POWER SUPPLY CIR 1 (Power supply circuit) |
Diagnosis condition | When Ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | The battery voltage sent to distance sensor (ICC sensor) remains less than 8.6 V for 5 seconds | ||
| Diagnosis delay time | — | ||
| C1A01–17 |
POWER SUPPLY CIR 1 (Power supply circuit 1) |
Diagnosis condition | When Ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | The battery voltage sent to distance sensor (ICC sensor) remains more than 16.5 V | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
Connector, harness, fuse
-
Distance sensor (ICC sensor)
FAIL-SAFE
The following systems are canceled:
-
Intelligent Cruise Control
-
Automatic Emergency Braking (AEB)
-
Intelligent Forward Collision Warning (I-FCW)
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Start the engine.
-
Turn the MAIN switch of ICC system ON.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the “C1A01–16” or “C1A01–17” is detected as the current malfunction in “Self Diagnostic Result” mode of “LASER/RADAR”.
Is “C1A01–16” or “C1A01–17” detected as the current malfunction?
YES>>Refer to Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CHECK DISTANCE SENSOR (ICC SENSOR) POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit of distance sensor (ICC sensor). Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Replace the distance sensor (ICC sensor). Refer to Removal and Installation.
NO>>Repair or replace the malfunctioning parts.
C1a0c Adas Message Counter Failure
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT terms DTC detection condition
C1A0C (82, 83)
ADAS MSG COUNTER
Diagnosis condition
When ignition switch is ON...
C1a03 Vehicle Speed Sensor
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition
C1A03–64
VHCL SPEED SE CIRC
(Nissan Murano Vehicle speed sensor circuit)
Diagnosis condition
When ignition switch in ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis System (lane Camera Unit)
CONSULT Function (LANE CAMERA UNIT) APPLICATION ITEMSCONSULT performs the following functions by communicating with the lane camera unit. Diagnosis mode Description Work support Performs the camera aiming. Self Diagnostic Result Displays the name of a malfunctioning system stored in the lane camera unit Data Monitor Displays lane camera unit input/output data in real time Ecu Identification Displays lane camera unit part number CAN Diag Support Monitor Displays a reception/transmission state of CAN communication Configuration The Nissan Murano vehicle specification that is written in lane camera unit can be displayed or stored The vehicle specification can be written when lane camera unit is replaced SELF DIAGNOSTIC RESULTRefer to DTC Index...
Nissan Murano (Z52) 2015-2024 Service Manual: Relay Control System
System Description SYSTEM DIAGRAMSystem DescriptionIPDM E/R activates the internal control circuit to perform the relay ON-OFF control according to the input signals from various sensors and the request signals received from control units via CAN communication...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Power Steering Fluid (PSF)
- Rear bench seat adjustment
- Shift lock release
- New on site
- Most important about car
Vehicle security system
Your vehicle has two types of security systems:
Vehicle security system NISSAN Vehicle Immobilizer SystemThe vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
