Nissan Murano: Power Supply and Ground Circuit / Av Control Unit
CHECK FUSE
Check that the following fuses are not blown:
| Terminal No. | Signal name | Fuse No. | Capacity |
|---|---|---|---|
| 7 | ACC power supply | 7 | 10 A |
| 17 | Ignition power supply | 29 | 10 A |
| 19 | Battery power supply | 15 | 20 A |
Are the fuses blown?
YES>>Replace the blown fuse after repairing the affected circuit.
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect AV control unit connectors.
-
Check voltage between AV control unit connectors and ground.
AV control unit Ground Condition Voltage
(Approx.)Connector Terminal M161 19 — Ignition switch: OFF Battery voltage 7 Ignition switch: ON 17
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connectors.
CHECK GROUND CIRCUIT
-
Ignition switch OFF.
-
Check continuity between AV control unit connector and ground.
AV control unit Ground Continuity Connector Terminal M161 20 — Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness or connectors.
Bose Speaker Amp
Diagnosis Procedure
CHECK FUSE
Check that the following fuses are not blown:
Terminal No. Signal name Fuse No. Capacity
10
Battery power supply
11
15 A
11
Battery power supply
12
15 A
Are the fuses blown?
YES>>
Replace the blown fuse after repairing the affected circuit...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P0706 Transmission Range Sensor a
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0706 T/M RANGE SENSOR A (Transmission Range Sensor A Circuit Range/Performance) Diagnosis condition TCM power supply voltage: More than 11 V Signal Transmission range switch signal Threshold All range signals stay OFF Diagnosis delay time Maintained for 30 seconds POSSIBLE CAUSE Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit between transmission range switch and TCM) Transmission range switch Control cable Harness or connector (CAN communication line is error)FAIL-SAFE Shift position indicator on combination meter is not displayed Selector shock is large Start is slow Acceleration is slow Lock-up is not performed DTC Confirmation Procedure PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test...
Nissan Murano (Z52) 2015-2024 Service Manual: Headlining
Exploded View WITH PANORAMIC ROOF GLASS 1. Headlining 2. Assist grip (without coat hanger) 3. Sun visor holder (LH/RH) 4. Sun visor (RH) 5. Sun visor cover (LH/RH) 6. Sun visor (LH) 7. Front room/map lamp assembly 8. Rear seat belt center retractor finisher 9...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- All-Wheel Drive (AWD) (if so equipped)
- Fuel recommendation
- Settings
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
