Nissan Murano: Dtc/circuit Diagnosis / Vdc Off Indicator Lamp
CHECK VDC OFF INDICATOR LAMP FUNCTION (1)
Check that VDC OFF indicator lamp in combination meter turns ON for 1 second after ignition switch ON.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Proceed to Diagnosis Procedure.
CHECK VDC OFF INDICATOR LAMP FUNCTION (2)
Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?
YES>>Inspection End.
NO>>Check the VDC OFF switch system. Refer to Diagnosis Procedure.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts.
CHECK VDC OFF INDICATOR LAMP SIGNAL (1)
CONSULT
-
Select “OFF LAMP” in “Data Monitor” mode of “ABS”.
-
Ignition switch OFF.
-
Check that “Data Monitor” displays “On” for 1 second after ignition switch ON and then changes to “Off”.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
CHECK VDC OFF INDICATOR LAMP SIGNAL (2)
CONSULT
-
Select “OFF LAMP” in “Data Monitor” mode of “ABS”.
-
Check that “Data Monitor” displays “On” or “Off” each time VDC OFF switch is operated.
Is the inspection result normal?
YES>>Replace the combination meter. Refer to Removal and Installation.
NO>>Check the VDC OFF switch system. Refer to Diagnosis Procedure.
Brake Warning Lamp
Component Function Check
CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for 1 second after ignition switch ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: B260f Eng State Sig Lost
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition B260F ENG STATE SIG LOST (Engine state signal lost) Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold BCM has not yet received the engine status signal from ECM when ignition switch is in the ON position...
Nissan Murano (Z52) 2015-2024 Service Manual: P0706 Transmission Range Sensor a
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0706 T/M RANGE SENSOR A (Transmission Range Sensor A Circuit Range/Performance) Diagnosis condition TCM power supply voltage: More than 11 V Signal Transmission range switch signal Threshold All range signals stay OFF Diagnosis delay time Maintained for 30 seconds POSSIBLE CAUSE Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit between transmission range switch and TCM) Transmission range switch Control cable Harness or connector (CAN communication line is error)FAIL-SAFE Shift position indicator on combination meter is not displayed Selector shock is large Start is slow Acceleration is slow Lock-up is not performed DTC Confirmation Procedure PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Memory storage function (key-link)
- Passenger compartment
- Rear bench seat adjustment
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
