Nissan Murano: Dtc/circuit Diagnosis / U1a10 Airbag Signal
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| U1A10 |
AIRBAG SIGNAL (Airbag signal) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Car crash information signal | ||
| Threshold | Abnormality | ||
| Diagnosis delay time | 1 second or more | ||
POSSIBLE CAUSE
CAN communication system
FAIL-SAFE
-
Some telematics system does not function
-
Inform a NissanConnect center about abnormality
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “TELEMATICS”.
-
Check DTC.
Is DTC U1A10 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
PERFORM SELF DIAGNOSTIC RESULT OF AIR BAG
CONSULT
-
Ignition switch ON.
-
Erase DTC.
-
Select “Self Diagnostic Result” mode of “AIR BAG”.
-
Check DTC.
Are any DTCs detected?
YES>>Refer to DTC Index.
NO>>GO TO 2.
PERFORM SELF DIAGNOSTIC RESULT OF TELEMATICS
CONSULT
-
Ignition switch ON.
-
Erase DTC.
-
Select “Self Diagnostic Result” mode of “TELEMATICS”.
-
Check DTC.
Is DTC U1A10 detected?
YES>>Replace TCU. Refer to Removal and Installation.
NO>>Refer to Intermittent Incident.
U1a0e Sos Switch on Stuck
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
U1A0E
SOS SWITCH ON STUCK
(SOS switch ON stuck)
Diagnosis condition
When ignition switch is ON...
Power Supply and Ground Circuit
Diagnosis Procedure
CHECK FUSE
Check that the following fuses are not blown:
Terminal No. Signal name Fuse No. Capacity
1
Battery power supply
25
10 A
2
ACC power supply
7
10 A
10
Ignition signal
29
10 A
Are the fuses blown?
YES>>
Replace the blown fuse after repairing the affected circuit...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Ldw
System Description SYSTEM DIAGRAMADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description ABS actuator and electric unit (control unit) CAN communication Nissan Murano Vehicle speed signal (ABS) Receives wheel speeds of four wheels BCM CAN communication Turn indicator signal Receives an operational state of the turn signal lamp and the hazard lamp Combination meter CAN communication System selection signal Receives a selection state of each item in “Driver Assistance” selected with the Nissan Murano vehicle information display Lane camera unit ITS communication Detected lane condition signal Receives detection results of lane marker Output Signal Item Reception unit Signal name Description Combination meter CAN communication Lane departure warning lamp signal Transmits a lane departure warning lamp signal to turn ON the lane departure warning lamp Lane camera unit ITS communication Nissan Murano Vehicle speed signal Transmits a vehicle speed calculated by the ADAS control unit Turn indicator signal Transmits a turn indicator signal received from BCM Warning system buzzer Warning buzzer signal Activates warning system buzzer...
Nissan Murano (Z52) 2015-2024 Service Manual: Distance Sensor (icc Sensor) Alignment
Work Procedure Always perform the radar alignment after removing and installing or replacing the distance sensor.Application Notice Type Description TYPE 1 When using KV99112700 for radar alignment. Refer to Description. TYPE 2 When using 1-20-2851-1 for radar alignment...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Intelligent Forward Collision Warning (I-FCW)
- Power Steering Fluid (PSF)
- High Beam Assist (if so equipped)
- New on site
- Most important about car
