Nissan Murano: Wiper & Washer :: Dtc/circuit Diagnosis / Rear Wiper Motor Circuit
CHECK REAR WIPER ON OPERATION
CONSULT
-
Select “RR WIPER” in “Active Test” mode of “BCM(WIPER)”.
-
While operating the test item, check rear wiper operation.
On : Rear wiper ON operation Off : Stop the rear wiper.
Is the inspection result normal?
YES>>Rear wiper motor circuit is normal.
NO>>Refer to Diagnosis Procedure.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT
-
Ignition switch OFF.
-
Disconnect rear wiper motor connector.
-
Ignition switch ON.
-
Select “RR WIPER” in “Active Test” mode of “BCM(WIPER)”.
-
While operating the test item, check voltage between rear wiper motor harness connector and ground.
| (+) | (−) | Condition |
Voltage (Approx.) | ||
|---|---|---|---|---|---|
| Rear wiper motor | |||||
| Connector | Terminal | ||||
| D553 | 1 | Ground | REAR WIPER | On | Battery voltage |
| Off | 0 V | ||||
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK REAR WIPER MOTOR CIRCUIT
-
Ignition switch OFF.
-
Disconnect BCM connector.
-
Check continuity between BCM harness connector and rear wiper motor harness connector.
BCM Rear wiper motor Continuity Connector Terminal Connector Terminal M20 95 D553 1 Yes -
Check continuity between BCM harness connector and ground.
BCM — Continuity Connector Terminal M20 95 Ground No
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness.
CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT
-
Ignition switch OFF.
-
Check continuity between rear wiper motor harness connector and ground.
| Rear wiper motor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| D553 | 3 | Ground | Yes |
Is the inspection result normal?
YES>>Replace rear wiper motor. Refer to Removal and Installation.
NO>>Repair or replace harness.
Washer Switch
Description
Washer switch is integrated with the combination switch (wiper and washer switch).
Combination switch (wiper and washer switch) switches polarity between front and rear washer operation to supply power and ground to the front and rear washer motor...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: In-Vehicle Sensor
Removal and Installation REMOVALRemove the instrument lower panel LH. Refer to Removal and Installation. Remove the screw (A) and in-Nissan Murano vehicle sensor (1). INSTALLATIONInstallation is in the reverse order of removal.CAUTION: Make sure that the aspirator hose is securely attached to the in-vehicle sensor when installing the instrument lower panel LH...
Nissan Murano (Z52) 2015-2024 Service Manual: Ecu Diagnosis Information. Ecm
Values on the Diagnosis Tool NOTE: The following table includes information (items) inapplicable to this Nissan Murano vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Numerical values in the following table are reference values...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Intelligent Forward Collision Warning (I-FCW)
- Rear bench seat adjustment
- Warning lights
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
