Nissan Murano: Dtc/circuit Diagnosis / P0719 Brake Pedal Switch B

Nissan Murano (Z52) 2015-2024 Service Manual / Engine / Engine Control System :: Vq35de / Dtc/circuit Diagnosis / P0719 Brake Pedal Switch B

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0719

Brake pedal switch B

(Brake Switch "B" Circuit Low) 		Diagnosis condition

  • When a deceleration G of -0.13 G or more occurs after the Nissan Murano vehicle speed exceeds 30 km/h (19 MPH).

  • When the brake normal close switch (Brake pedal position switch) is pressed.
Signal (terminal) Stop lamp switch signal
Threshold The stop lamp switch is released until 2 seconds have passed after the Nissan Murano vehicle has stopped when the diagnosis condition is established. Malfunction is confirmed when the above condition is established 5 times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open.)

  • Stop lamp switch

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Repeat the following step 5 times.

    1. Drive the Nissan Murano vehicle and accelerate to 48 km/h (30 MPH).

    2. Decelerate from 48 km/h (30 MPH) to 0 km/h (0 MPH) within 7 seconds.

    3. Stop the Nissan Murano vehicle for 2 seconds or more.

      CAUTION:

      Always drive vehicle at a safe speed.

      NOTE:

      This procedure may be conducted with the drive wheels lifted in the shop or by driving the Nissan Murano vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

  3. Check DTC.

Is DTC P0719 detected?

YES>>

Refer to Diagnosis Procedure .

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK STOP LAMP SWITCH CIRCUIT

  1. Turn ignition switch OFF.

  2. Depress the brake pedal and check the stop lamp when releasing.

    Brake pedal Stop lamp
    Fully released Not illuminated
    Slightly depressed Illuminated

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH POWER SUPPLY

  1. Disconnect stop lamp switch harness connector.

  2. Check the voltage between stop lamp switch harness connector and ground.

    + − Voltage
    Stop lamp switch
    Connector Terminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK FUSE

  1. Pull out 10A fuse (No. 10) from fuse block (J/B).

  2. Check that 10A fuse is not blowing.

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

Perform trouble diagnosis for power supply circuit.

CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT

  1. Disconnect stop lamp switch harness connector.

  2. Disconnect ECM harness connector.

  3. Check the continuity between stop lamp switch harness connector and ECM harness connector.

    Stop lamp switch ECM Continuity
    Connector Terminal Connector Terminal
    E38 2 E32 139 Existed

  4. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning part.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to Component Inspection (Stop Lamp Switch).

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace stop lamp switch. Refer to Exploded View.

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

>>

INSPECTION END

Component Inspection

CHECK STOP LAMP SWITCH-I

  1. Turn ignition switch OFF.

  2. Disconnect stop lamp switch harness connector.

  3. Check the continuity between stop lamp switch harness connector terminals as per the following conditions.

    Stop lamp switch Condition Continuity
    + –
    Terminal
    1 2 Brake pedal Fully released Not existed
    Slightly depressed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH-II

  1. Adjust stop lamp switch installation. Refer to Adjustment.

  2. Check the continuity between stop lamp switch harness connector terminals as per the following conditions.

    Stop lamp switch Condition Continuity
    + –
    Terminal
    1 2 Brake pedal Fully released Not existed
    Slightly depressed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace stop lamp switch. Refer to Exploded View.

    P0643 Sensor Power Supply

    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 2 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the short-circuited sensor...

    P0850 Pnp Switch

    DTC Description DESCRIPTIONWhen the selector lever position is P or N, park/neutral position (PNP) signal from the transmission range switch is sent to ECM...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: A/c Auto Amp.


    Values on the Diagnosis Tool NOTE: The following table includes information (items) inapplicable to this Nissan Murano vehicle: For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor item Condition Value/Status AMB TEMP SEN Ignition switch ON — Equivalent to ambient temperature IN-VEH TEMP Ignition switch ON — Equivalent to in-Nissan Murano vehicle temperature (front side) INT TEMP SEN Ignition switch ON — Equivalent to front evaporator fin temperature SUNLOAD SEN Ignition switch ON — Equivalent to sunload (driver side) AMB SEN CAL Ignition switch ON — Equivalent to ambient temperature IN-VEH CAL Ignition switch ON — Equivalent to in-Nissan Murano vehicle temperature (front side) INT TEMP CAL Ignition switch ON — Equivalent to front evaporator fin temperature SUNL SEN CAL Ignition switch ON — Equivalent to sunload (driver side) COMP REQ SIG Engine: Run at idle after warming up A/C switch: ON (Compressor operation status ON) On A/C switch: OFF (Compressor operation status OFF) Off FAN REQ SIG Engine: Run at idle after warming up Front blower motor: ON On Front blower motor: OFF Off FAN DUTY Engine: Run at idle after warming up Front blower motor: ON 25 – 81 Front blower motor: OFF 0 XM Ignition switch ON — Value according to target air flow temperature (driver side) PA TARGET A/TEMP Ignition switch ON — Value according to target air flow temperature (passenger side) ENG COOL TEMP Ignition switch ON — Equivalent to engine coolant temperature Nissan Murano Vehicle SPEED Driving — Equivalent to speedometer reading PASS SUNL CAL Ignition switch ON — Equivalent to sunload (passenger side) PASS SUNL SEN CAL Ignition switch ON — Equivalent to sunload (passenger side) Reference Value TERMINAL LAYOUTPHYSICAL VALUES Terminal No...

    Nissan Murano (Z52) 2015-2024 Service Manual: Air Mix Door Motor Rh


    Diagnosis Procedure CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY Ignition switch ON. Check voltage between air mix door motor RH harness connector and ground. + − Voltage (Approx.) Air mix door motor RH Connector Terminal M156 1 Ground Battery voltage Is the inspection result normal? YES>> GO TO 2...

    Categories

    Fuel gauge

    Nissan Murano. Fuel gauge

    The gauge indicates the approximate fuel level in the tank.

    The gauge may move slightly during braking, turning, acceleration, or going up or down hills.

    The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.

    read more

     
    Copyright © 2026 www.nimurano.com