Nissan Murano: Dtc/circuit Diagnosis / P0037 Ho2s2 Heater

Nissan Murano (Z52) 2015-2024 Service Manual / Engine / Engine Control System :: Vq35de / Dtc/circuit Diagnosis / P0037 Ho2s2 Heater

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0037

HO2S2 HTR (B1)

(HO2S heater control circuit low bank 1 sensor 2)
A Diagnosis condition
Signal (terminal) Voltage signal transmitted from heated oxygen sensor 2 heater to ECM
Threshold An excessively low voltage signal is sent to ECM through the heated oxygen sensor 2 heater
Diagnosis delay time
B Diagnosis condition
Signal (terminal)
Threshold ECM detects the heated oxygen sensor 2 heater circuit is short to ground.
Diagnosis delay time
P0038

HO2S2 HTR (B1)

(HO2S heater control circuit high bank 1 sensor 2)
Diagnosis condition
Signal (terminal) Voltage signal transmitted from heated oxygen sensor 2 heater to ECM
Threshold An excessively high voltage signal is sent to ECM through the heated oxygen sensor 2 heater
Diagnosis delay time
P0057

HO2S2 HTR (B2)

(HO2S heater control circuit low bank 2 sensor 2)
A Diagnosis condition
Signal (terminal) Voltage signal transmitted from heated oxygen sensor 2 heater to ECM
Threshold An excessively low voltage signal is sent to ECM through the heated oxygen sensor 2 heater
Diagnosis delay time
B Diagnosis condition
Signal (terminal)
Threshold ECM detects the heated oxygen sensor 2 heater circuit is short to ground.
Diagnosis delay time
P0058

HO2S2 HTR (B2)

(HO2S heater control circuit high bank 2 sensor 2)
Diagnosis condition
Signal (terminal) Voltage signal transmitted from heated oxygen sensor 2 heater to ECM
Threshold An excessively high voltage signal is sent to ECM through the heated oxygen sensor 2 heater
Diagnosis delay time

POSSIBLE CAUSE

P0037

  • Harness or connectors (The heated oxygen sensor 2 heater circuit is open or shorted.)

  • Heated oxygen sensor 2 heater

P0038

  • Harness or connectors (The heated oxygen sensor 2 heater circuit is shorted.)

  • Heated oxygen sensor 2 heater

P0057

  • Harness or connectors (The heated oxygen sensor 2 heater circuit is open or shorted.)

  • Heated oxygen sensor 2 heater

P0058

  • Harness or connectors (The heated oxygen sensor 2 heater circuit is shorted.)

  • Heated oxygen sensor 2 heater

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 10.5 V and 16 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to the normal operating temperature.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.

  6. Let engine idle for 1 minute.

  7. Check 1st trip DTC.

Is 1st tip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HO2S2 POWER SUPPLY

  1. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between HO2S2 harness connector and ground.

    DTC HO2S2 Ground Voltage
    Bank Connector Terminal
    P0037, P0038 1 F62 1 Ground Battery voltage
    P0057, P0058 2 F54 1

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK HO2S2 SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between HO2S2 harness connector and IPDM E/R harness connector.

DTC HO2S2 IPDM E/R Continuity
Bank Connector Terminal Connector Terminal
P0037, P0038 1 F62 1 F19 52 Existed
P0057, P0058 2 F54 1 53

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK HO2S2 HEATER OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between HO2S2 harness connector and ECM harness connector.

    DTC HO2S2 ECM Continuity
    Bank Connector Terminal Connector Terminal
    P0037, P0038 1 F62 2 F78 7 Existed
    P0057, P0058 2 F54 2 47
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK HEATED OXYGEN SENSOR 2 HEATER

Check heated oxygen sensor 2 heater. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning heated oxygen sensor 2. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

Component Inspection

CHECK HEATED OXYGEN SENSOR 2 HEATER

  1. Turn ignition switch OFF.

  2. Disconnect heated oxygen sensor 2 harness connector.

  3. Check resistance between HO2S2 terminals as per the following.

    + Resistance
    Heated oxygen sensor 2
    Terminal
    1 2 3.0 Ω [at 25°C (77°F)]
    3 1

    ∞Ω

    (Continuity should not exist)
    2
    4
    4 1
    2
    3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning heated oxygen sensor 2. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

    P0031 A/f Sensor 1 Heater

    DTC Description DTC DETECTION LOGIC Deterioration in A/F sensor 1 heater performance. The current amperage in the A/F sensor 1 heater circuit is out of the normal range...

    P0053 A/f Sensor 1 Heater

    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0053 HO2S1 HTR B1 (HO2S heater resistance bank 1 sensor 1) Diagnosis condition — Signal (terminal) A/F sensor 1 heater (bank 1) signal Threshold During engine running, weighted average of A/F sensor internal resistance is out of the normal range Diagnosis delay time — POSSIBLE CAUSE Harness and connectors [A/F sensor 1 (bank 1) heater circuit is open or shorted...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Service Data and Specifications (sds). Service Data and Specifications (sds)


    General Specifications Applied model Axle AWD Engine VQ35DE Transaxle CVT Transfer model TY21C Gear ratio 0.404 Number of teeth Ring gear 42 Drive pinion 17 Oil capacity Refer to Fluids and Lubricants. Preload Torque Unit: N·m (kg-m, in-lb) Item Standard Pinion bearing preload (P1) 0...

    Nissan Murano (Z52) 2015-2024 Service Manual: I-Li


    System Description SYSTEM DIAGRAMADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description ECM CAN communication Brake pedal position switch signal Receives Brake pedal position switch state Accelerator pedal position signal Receives accelerator pedal position (angle) Stop lamp switch signal Receives stop lamp switch state Engine speed signal Receives engine speed TCM CAN communication Input speed signal Receives the number of revolutions of input shaft Current gear position signal Receives a current gear position Shift position signal Receives a selector lever position Output shaft revolution signal Receives the number of revolutions of output shaft ABS actuator and electric unit (control unit) CAN communication ABS malfunction signal Receives a malfunction state of ABS ABS operation signal Receives an operational state of ABS TCS malfunction signal Receives a malfunction state of TCS TCS operation signal Receives an operational state of TCS VDC OFF switch signal Receives an ON/OFF state of VDC VDC malfunction signal Receives a malfunction state of VDC VDC operation signal Receives an operational state of VDC Nissan Murano Vehicle speed signal (ABS) Receives wheel speeds of four wheels Yaw rate signal Receives yaw rate acting on the Nissan Murano vehicle Side G sensor signal Receives lateral G acting on the Nissan Murano vehicle Combination meter CAN communication Parking brake switch signal Receives an operational state of the parking brake System selection signal Receives a selection state of each item in "Driver Assistance" BCM CAN communication Turn indicator signal Receives an operational state of the turn signal lamp and the hazard lamp Steering angle sensor CAN communication Steering angle sensor malfunction signal Receives a malfunction state of steering angle sensor Steering angle sensor signal Receives the number of revolutions, turning direction of the steering wheel Steering angle speed signal Receives the turning angle speed of the steering wheel Lane intervention switch Lane intervention switch signal Receives an ON/OFF state of the lane intervention switch Lane camera unit ITS communication Detected lane condition signal Receives detection results of lane marker Output Signal Item Reception unit Signal name Description ABS actuator and electric unit (control unit) CAN communication Target yaw moment signal Transmits a target yaw moment signal to generate yaw moment to the Nissan Murano vehicle Combination meter CAN communication Intelligent Lane Intervention ON indicator lamp signal Transmits an Intelligent Lane Intervention ON indicator lamp signal to turn ON the Intelligent Lane Intervention ON indicator lamp Lane departure warning lamp signal Transmits an lane departure warning lamp signal to turn ON the lane departure warning lamp Lane camera unit ITS communication Nissan Murano Vehicle speed signal Transmits a vehicle speed calculated by the ADAS control unit Turn indicator signal Transmits a turn indicator signal received from BCM Steering assist system ON indicator Steering assist system ON indicator signal Turns ON the steering assist system ON indicator Intelligent Lane Intervention system ON indicator Intelligent Lane Intervention system ON indicator signal Turns ON the Intelligent Lane Intervention system ON indicator Warning system buzzer Warning buzzer signal Activates warning system buzzer...

    Categories

    read more

     
    Copyright © 2026 www.nimurano.com