Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / Mirror Sensor. Lh

Nissan Murano (Z52) 2015-2024 Service Manual / Body Interior / Automatic Drive Positioner :: Dtc/circuit Diagnosis / Mirror Sensor. Lh

Component Function Check

DATA MONITOR

CONSULT

  1. Select “MIR/SEN LH U-D”, “MIR/SEN LH R-L” in “Data Monitor” mode of “AUTO DRIVE POS.”.

  2. Check that the function operates normally according to the following conditions:

    Monitor item Condition Value
    MIR/SEN LH U-D Door mirror LH Close to peak 3.4V
    Close to valley 0.6V
    MIR/SEN LH R-L Close to right edge 3.4V
    Close to left edge 0.6V

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Perform diagnosis procedure. Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK DOOR MIRROR LH SENSOR SIGNAL

  1. Ignition switch ACC.

  2. Check voltage between door mirror LH harness connector and ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    Door mirror LH
    Connector Terminal
    D4 3 Ground

    Door mirror

    LH     		Close to peak 3.4V
    Close to valley 0.6V
    15 Close to right edge 3.4V
    Close to left edge 0.6V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 2.

CHECK DOOR MIRROR LH SENSOR CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect automatic drive positioner control unit and door mirror LH connector.

  3. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.

    Automatic drive positioner control unit Door mirror LH Continuity
    Connector Terminal Connector Terminal
    M33 6 D4 3 Yes
    18 15

  4. Check continuity between automatic drive positioner control unit harness connector and ground.

    Automatic drive positioner control unit Ground Continuity
    Connector Terminal
    M33 6 No
    18

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK DOOR MIRROR LH SENSOR CIRCUIT 2

  1. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.

    Automatic drive positioner control unit Door mirror LH Continuity
    Connector Terminal Connector Terminal
    M33 20 D4 16 Yes
    21 4

  2. Check continuity between automatic drive positioner control unit harness connector and ground.

    Automatic drive positioner control unit Ground Continuity
    Connector Terminal
    M33 20 No
    21

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK TILT MOTOR ADJUSTING OPERATION

  1. Connect automatic drive positioner control unit and door mirror LH.

  2. Ignition switch ON.

  3. Check tilt motor adjusting operation with memory function.

Is the operation normal?

YES>>

Replace door mirror actuator (built into door mirror LH). Refer to Removal and Installation.

NO>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

NO>>

Repair or replace the malfunctioning part.

    Telescopic Sensor

    Component Function Check DATA MONITOR CONSULT Select “TELESCO PULSE” in “Data Monitor” mode of “AUTO DRIVE POS.”. Check that the function operates normally according to the following conditions: Monitor item Condition Value TELESCO PULSE Steering column Operate (forward) Change (decrease) Operate (backward) Change (increase) Release No change Is the inspection result normal? YES>> Inspection End...

    Sliding Motor

    Component Function Check ACTIVE TEST CONSULT Select “SEAT SLIDE” in “Active Test” mode of “AUTO DRIVE POS.”. Check that the function operates normally...

    Other information:

    Nissan Murano (Z52) 2015-2024 Owners Manual: Power Windows


    WARNING Make sure that all passengers have their hands, etc., inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. To help avoid risk of injury or death through unintended operation of the vehicle and/or its systems, including entrapment in windows or inadvertent door lock activation, do not leave children, people who require the assistance of others or pets unattended in your vehicle...

    Nissan Murano (Z52) 2015-2024 Owners Manual: Unfastening the seat belts. Checking seat belt operation


    Unfastening the seat belts To unfasten the seat belt, press the button on the buckle . The seat belt automatically retracts. Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods: When the seat belt is pulled quickly from the retractor When the vehicle slows down rapidly To increase your confidence in the seat belts, check the operation as follows: Grasp the shoulder belt and pull forward quickly...

    Categories

    Vehicle security system

    Nissan Murano. Vehicle security system

    Your vehicle has two types of security systems:

    Vehicle security system NISSAN Vehicle Immobilizer System

    The vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.

    read more

     
    Copyright © 2026 www.nimurano.com