Nissan Murano: Steering System :: Dtc/circuit Diagnosis / Heated Steering Wheel Switch Indicator Lamp

Nissan Murano (Z52) 2015-2024 Service Manual / Steering / Steering System :: Dtc/circuit Diagnosis / Heated Steering Wheel Switch Indicator Lamp

Component Function Check

CHECK HEATED STEERING WHEEL SWITCH INDICATOR LAMP

  1. Ignition switch ON.

  2. Turn heated steering wheel switch ON. Observe indicator.

  3. Turn heated steering wheel switch OFF. Observe indicator.

Does heated steering wheel switch indicator lamp turn ON and then OFF?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK POWER CIRCUIT

  1. Ignition switch OFF.

  2. Remove the heated steering wheel switch. Refer to Removal and Installation.

  3. Ignition switch ON.

  4. Check voltage between heated steering wheel switch harness connector terminals.

    Heated steering wheel switch

    Voltage

    (Approx.)
    Connector Terminals
    + -
    M48 6 8 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect heated steering wheel switch connector.

  3. Check continuity between heated steering wheel switch harness connector terminal and ground.

Heated steering wheel switch — Continuity
Connector Terminal
M48 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND HEATED STEERING WHEEL SWITCH

  1. Disconnect heated steering wheel relay connector.

  2. Check continuity between heated steering wheel relay harness connector terminal and heated steering wheel switch harness connector terminal.

    Heated steering wheel relay Heated steering wheel switch Continuity
    Connector Terminal Connector Terminal
    M90 5 M48 5 Yes

  3. Check continuity between heated steering wheel relay harness connector terminal and ground.

    Heated steering relay — Continuity
    Connector Terminal
    M90 5 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK HEATED STEERING WHEEL RELAY

Check heated steering wheel relay. Refer to Component Inspection (Heated Steering Wheel Relay).

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace heated steering wheel relay.

CHECK BATTERY POWER

Check the following:

  • Battery

  • Harness for open or short between battery and 10A fuse (No. 6)

  • 10A fuse (No. 6)

  • Harness for open or short between 10A fuse (No. 6) and heated steering wheel relay

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair harness or connector.

CHECK HARNESS BETWEEN A/C AUTO AMP. AND HEATED STEERING WHEEL SWITCH

  1. Disconnect A/C auto amp. connector.

  2. Check continuity between A/C auto amp. harness connector terminal and heated steering wheel switch harness connector terminal.

    A/C auto amp. Heated steering wheel switch Continuity
    Connector Terminal Connector Terminal
    M50 8 M48 6 Yes

  3. Check continuity between A/C auto amp. harness connector terminal and ground.

    A/C auto amp. — Continuity
    Connector Terminal
    M50 8 Ground No

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair harness or connector.

CHECK HEATED STEERING WHEEL SWITCH

Check heated steering wheel switch. Refer to Component Inspection (Heated Steering Wheel Switch).

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Replace heated steering wheel switch. Refer to Removal and Installation.

    Heated Steering Wheel System

    Component Function Check CHECK HEATED STEERING WHEEL SYSTEM Check operation of heated steering wheel system. Refer to System Description. Is the inspection result normal? YES>> Inspection End...

    Steering System :: Symptom Diagnosis

    ..

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: B2720 Corner Sensor [rl]


    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2720–60 CORNER SENSOR [RL] (Rear sonar sensor LH outer) — Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (reset error) Diagnosis delay time — B2720–61 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (configuration error) Diagnosis delay time — B2720–62 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (power supply error) Diagnosis delay time — B2720–63 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (self diag result) Diagnosis delay time — B2720–65 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (over temperature) Diagnosis delay time — B2720–66 Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor LH outer signal (terminal 22) Threshold Rear sonar sensor LH outer signal circuit is open or short to ground Diagnosis delay time — B2720–67 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (diag dump error) Diagnosis delay time — B2720–68 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (resonator error) Diagnosis delay time — B2720–83 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (CRC error) Diagnosis delay time — B2720–92 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Rear sonar sensor LH outer internal failure (membrane error) Diagnosis delay time — POSSIBLE CAUSE Harness or connectors Rear sonar sensor LH outer FAIL-SAFE Obstacle detection of rear sonar sensor LH outer is stopped Audible warning (sonar buzzer) of all sensors is stopped Sonar buzzer sounds for 3 seconds DTC Confirmation Procedure DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...

    Nissan Murano (Z52) 2015-2024 Service Manual: P17f0 Cvt Judder (t/m Inspection)


    DTC Description NOTE: The customer reports CVT judder (shake, shudder, single or multiple bumps or vibration) hesitation on acceleration, lack of power or RPM flare. If DTC P17F0 is detected on his/her Nissan Murano vehicle, this diagnosis is required...

    Categories

    Front manual seat adjustment (if so equipped)

    Your vehicle seats can be adjusted manually. For additional information about adjusting the seats, refer to the steps outlined in this section.

    Forward and backward

    Nissan Murano. Front manual seat adjustment (if so equipped)

    read more

     
    Copyright © 2026 www.nimurano.com