Nissan Murano: Automatic Drive Positioner :: Basic Inspection / Diagnosis and Repair Work Flow

Nissan Murano (Z52) 2015-2024 Service Manual / Body Interior / Automatic Drive Positioner :: Basic Inspection / Diagnosis and Repair Work Flow

Work Flow

WORK FLOW

DETAILED FLOW

GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred).

GO TO 2.

CHECK DTC

CONSULT

Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Refer to DTC Index.

Is any symptom described and is any DTC displayed?

Symptom is described, DTC is displayed.>>

GO TO 3.

Symptom is not described, DTC is displayed.>>

GO TO 5.

Symptom is described, DTC is not displayed.>>

GO TO 4.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

GO TO 5.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE

Perform the confirmation procedure for the detected DTC.

Is the DTC displayed?

YES>>

GO TO 8.

NO>>

Check intermittent incident. Refer to Intermittent Incident.

PERFORM BASIC INSPECTION

Isolate the malfunctioning point with a basic inspection.

GO TO 7.

DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE

Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4 and determine the trouble diagnosis order based on possible causes and symptom.

GO TO 8.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the component diagnosis.

GO TO 9.

REPAIR OR REPLACE

Repair or replace the malfunctioning part.

GO TO 10.

FINAL CHECK

Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is detected) again, and then check that the malfunction can be repaired securely.

Are all malfunctions corrected?

YES>>

Inspection End.

Symptom is detected.>>

GO TO 6.

DTC is detected.>>

GO TO 8 .

Automatic Drive Positioner :: Basic Inspection

Inspection and Adjustment

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Variable Induction Air System

System Description SYSTEM DIAGRAMSYSTEM DESCRIPTIONIn the medium speed range, the ECM sends the ON signal to the VIAS control solenoid valve. This signal introduces the intake manifold vacuum into the power valve actuator and therefore closes the power valve...

Nissan Murano (Z52) 2015-2024 Service Manual: Ecu Diagnosis Information. Adas Control Unit 2

Values on the Diagnosis Tool NOTE: The following table includes information (items) inapplicable to this Nissan Murano vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor item Condition Value/Status MAIN SW Ignition switch ON When MAIN switch is pressed On When MAIN switch is not pressed Off SET/COAST SW Ignition switch ON When SET/COAST switch is pressed On When SET/COAST switch is not pressed Off CANCEL SW Ignition switch ON When CANCEL switch is pressed On When CANCEL switch is not pressed Off RESUME/ACC SW Ignition switch ON When RESUME/ACCELERATE switch is pressed On When RESUME/ACCELERATE switch is not pressed Off DISTANCE SW Ignition switch ON When DISTANCE switch is pressed On When DISTANCE switch is not pressed Off CRUISE OPE Drive the Nissan Murano vehicle and activate the vehicle-to-vehicle distance control mode When ICC system is controlling On When ICC system is not controlling Off BRAKE SW Ignition switch ON When brake pedal is depressed Off When brake pedal is not depressed On STOP LAMP SW Ignition switch ON When brake pedal is depressed On When brake pedal is not depressed Off IDLE SW Engine running Idling On Except idling (depress accelerator pedal) Off VHCL SPEED SE While driving Displays the Nissan Murano vehicle speed calculated by ADAS control unit ENGINE RPM Engine running Equivalent to tachometer reading THRTL SENSOR NOTE: The item is displayed, but it is not used...