Nissan Murano: Dtc/circuit Diagnosis / B1328 External Microphone 1
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| B1328–13 |
External Microphone 1 (Microphone) |
[OPEN] | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
| B1328–11 | [GND–SHORT] | Diagnosis condition | When ignition switch is ON. | |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
| B1328–12 | [VB–SHOR] | Diagnosis condition | When ignition switch is ON. | |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
POSSIBLE CAUSE
-
Microphone is not connected
-
Harness or connector
FAIL-SAFE
Microphone is inoperative
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1328 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
DETERMINE MALFUNCTION TYPE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1328–11, 12 or 13 detected?
YES>>13 [OPEN] or 11 [GND–SHORT] – GO TO 2.
YES>>12 [VB–SHOR] – GO TO 3.
NO>>Refer to Intermittent Incident.
CHECK MICROPHONE CIRCUITS FOR OPEN
-
Ignition switch OFF.
-
Disconnect AV control unit connector and microphone connector.
-
Check the continuity between AV control unit connector and microphone connector.
AV control unit Microphone Continuity Connector Terminal Connector Terminal M162 39 R8 4 Yes 40 1 51 5 59 2 -
Check the continuity between AV control unit connector and ground.
AV control unit Ground Continuity Connector Terminal M162 39 — No 40 51
Is the inspection result normal?
YES>>Replace microphone. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
CHECK MICROPHONE CIRCUITS FOR SHORT TO POWER SUPPLY
-
Ignition switch ON.
-
Check the voltage between AV control unit connector and ground.
AV control unit Ground Voltage
(Approx.)Connector Terminal M162 39 — 0 V 40 51 59
Is the inspection result normal?
YES>>Replace microphone. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
B1321 Front Right Tweeter
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1321–13
Front right tweeter
(Instrument panel tweeter RH)
[OPEN]
Diagnosis condition
When ignition switch is ON...
B132a External Usb
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B132A–13
External USB
(USB)
[OPEN]
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Owners Manual: Memory storage function (switch)
Use the following process to manually store the two memory positions in the switch: The vehicle should be stopped while setting the memory. Adjust the driver’s seat, steering columnand outside mirrors to the desired positions by manually operating each adjusting switch...
Nissan Murano (Z52) 2015-2024 Service Manual: System Description. Structure and Operation
Sectional View Drive gear Side bearing Differential case Pinion mate shaft Side gear Pinion mate gear Drive pinion Collapsible spacer AWD solenoid Stud bolt Electric controlled coupling Pinion front bearing Pinion rear bearing Electric Controlled Coupling The electric controlled coupling operates as the AWD system...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Vehicle Dynamic Control (VDC) OFF switch
- Turning the AEB system on/off
- High Beam Assist (if so equipped)
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
