Nissan Murano: Dtc/circuit Diagnosis / B1305 Control Unit Internal Fault

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Display Audio System - With 8" Color Display / Dtc/circuit Diagnosis / B1305 Control Unit Internal Fault

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B1305–04

Control unit internal error

(Audio unit internal fault)
[—] Diagnosis condition When ignition switch is ON.
Signal (terminal) –
Threshold Internal fault
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

Audio unit internal fault

FAIL-SAFE

Audio unit internal error

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1305–04 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1305–04 detected?

YES>>

Replace audio unit. Refer to Removal and Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis

    ..

    B130b Rear Right Speaker

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B130B–13 Rear RH speaker (Rear door speaker RH) [OPEN] Diagnosis condition When ignition switch is ON...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Trouble Diagnosis - Specification Value


    Description ECM input/output valve when the engine control system operates normally.NOTE: The SP value is indicated when “DISPLAY TYPE” is “Line Graph”. When the indicated value of “DATA MONITOR” mode is within the SP value, the engine control system is confirmed OK...

    Nissan Murano (Z52) 2015-2024 Service Manual: A/c Auto Amp.


    Values on the Diagnosis Tool NOTE: The following table includes information (items) inapplicable to this Nissan Murano vehicle: For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor item Condition Value/Status AMB TEMP SEN Ignition switch ON — Equivalent to ambient temperature IN-VEH TEMP Ignition switch ON — Equivalent to in-Nissan Murano vehicle temperature (front side) INT TEMP SEN Ignition switch ON — Equivalent to front evaporator fin temperature SUNLOAD SEN Ignition switch ON — Equivalent to sunload (driver side) AMB SEN CAL Ignition switch ON — Equivalent to ambient temperature IN-VEH CAL Ignition switch ON — Equivalent to in-Nissan Murano vehicle temperature (front side) INT TEMP CAL Ignition switch ON — Equivalent to front evaporator fin temperature SUNL SEN CAL Ignition switch ON — Equivalent to sunload (driver side) COMP REQ SIG Engine: Run at idle after warming up A/C switch: ON (Compressor operation status ON) On A/C switch: OFF (Compressor operation status OFF) Off FAN REQ SIG Engine: Run at idle after warming up Front blower motor: ON On Front blower motor: OFF Off FAN DUTY Engine: Run at idle after warming up Front blower motor: ON 25 – 81 Front blower motor: OFF 0 XM Ignition switch ON — Value according to target air flow temperature (driver side) PA TARGET A/TEMP Ignition switch ON — Value according to target air flow temperature (passenger side) ENG COOL TEMP Ignition switch ON — Equivalent to engine coolant temperature Nissan Murano Vehicle SPEED Driving — Equivalent to speedometer reading PASS SUNL CAL Ignition switch ON — Equivalent to sunload (passenger side) PASS SUNL SEN CAL Ignition switch ON — Equivalent to sunload (passenger side) Reference Value TERMINAL LAYOUTPHYSICAL VALUES Terminal No...

    Categories

    Luggage hooks

    Nissan Murano. Luggage hooks

    When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.

    The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.

    read more

     
    Copyright © 2026 www.nimurano.com