Nissan Murano: Basic Inspection / Additional Service When Replacing Around View Monitor Control Unit

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Intelligent Around View Monitor with Navigation System / Basic Inspection / Additional Service When Replacing Around View Monitor Control Unit

Description

BEFORE REPLACEMENT

When replacing around view monitor control unit, save or print current vehicle specification with CONSULT configuration before replacement.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing around view monitor control unit.

AFTER REPLACEMENT

CAUTION:

When replacing around view monitor control unit, you must perform “After Replace ECU” with CONSULT.

Complete the procedure of “After Replace ECU” in order.

If you set incorrect “After Replace ECU”, incidents might occur.

Configuration is different for each Nissan Murano vehicle model. Confirm configuration of each vehicle model.

Work Procedure

SAVING VEHICLE SPECIFICATION

CONSULT

Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current Nissan Murano vehicle specification.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing around view monitor control unit.

GO TO 2.

REPLACE AROUND VIEW MONITOR CONTROL UNIT

Replace around view monitor control unit. Refer to Removal and Installation.

GO TO 3.

WRITING Nissan Murano Vehicle SPECIFICATION

CONSULT

Enter "Re/Programming, Configuration".
If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write Nissan Murano vehicle specification. Refer to Work Procedure.
If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configuration" to write Nissan Murano vehicle specification. Refer to Work Procedure.

GO TO 4.

OPERATION CHECK

Check that the operation of the around view monitor control unit and camera images (fixed guide lines and predictive course lines) are normal.

Work End.

Diagnosis and Repair Workflow

Work Flow OVERALL SEQUENCE Reference 1: Refer to CONSULT Function (Around View Monitor Control Unit) or CONSULT Function (Sonar Control Unit). Reference 2: Refer to DTC Index (Around View Monitor Control Unit) or DTC Index (Sonar Control Unit)...

Configuration (around View Monitor Control Unit)

Description Vehicle specification needs to be written with CONSULT because it is not written after replacing around view monitor control unit.Configuration has three functions as follows Function Description READ CONFIGURATION Reads the Nissan Murano vehicle configuration of current around view monitor control unit...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: B2416 Touch Sen R Open

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2416–1B TOUCH SEN R OPEN (Touch sensor right open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal (automatic back door control module connector terminal: 4) Threshold When one of the following conditions is satisfied Touch sensor RH circuit is open Disconnect touch sensor RH connector Diagnosis delay time – B2416–1E TOUCH SEN R OPEN (Touch sensor right open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal (automatic back door control module connector terminal: 4) Threshold When one of the following conditions is satisfied Touch sensor RH circuit is open Disconnect touch sensor RH connector Diagnosis delay time – POSSIBLE CAUSE Improper installation of touch sensor Touch sensor RH Harness or connectors (touch sensor circuit is open) Automatic back door control module FAIL-SAFEInhibit automatic back door system auto open/close function DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...

Nissan Murano (Z52) 2015-2024 Service Manual: Driver Assistance System Symptoms

Symptom Table CAUTION: Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected. NOTE: Before performing diagnosis, check that it is not a symptom caused by normal operation. Refer to the following: Intelligent Drive Alertness system: System Description Traffic Sign Recognition system: System Description Rear Automatic Braking system: System Description Blind Spot Warning system: System Description Rear Cross Traffic Alert system: System Description Intelligent Forward Collision Warning: System Description Lane Departure Warning system: System Description Intelligent Lane Intervention system: System Description Symptom Confirmation item Inspection item/Reference page LDW/I-LI/BSW/RCTA/TSR/I-DA/I-FCW/RAB system display does not illuminate All of system display does not illuminate System settings cannot be turned ON/OFF Refer to Diagnosis Procedure...