Nissan Murano: Dtc/circuit Diagnosis / P0607 Ecm
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | |
| P0607 |
ECM (Control module performance) |
Diagnosis condition | Ignition switch ON |
| Signal (terminal) | — | ||
| Threshold | ECM internal communication system is malfunctioning | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
ECM
FAIL-SAFE
| Engine operating condition in fail-safe mode | ||
|---|---|---|
| Fail safe mode | Nissan Murano Vehicle behavior | |
| ECM | Engine torque may be limited. | |
PRECONDITIONING
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Turn ignition switch ON (engine stopped) and wait least 10 seconds.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Check 1st trip DTC.
Is 1st trip DTC detected?
YES>>Proceed to Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: INSPECTION END
PERFORM DTC CONFIRMATION PROCEDURE
-
Turn ignition switch ON.
-
Erase DTC.
-
Perform DTC confirmation procedure. Refer to DTC Description.
Is the 1st trip DTC P0607 displayed again?
YES>>Replace ECM. Refer to Removal and Installation.
NO>>INSPECTION END
P0604 Ecm
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0604
ECM
[Internal control module random access memory (RAM) error]
Diagnosis condition
Ignition switch ON
Signal (terminal)
—
Threshold
Malfunction in the internal RAM of ECM
Diagnosis delay time
—
POSSIBLE CAUSE
ECM
FAIL-SAFE Engine operating condition in fail-safe mode
Fail safe mode Nissan Murano Vehicle behavior
ECM
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx...
P062f Ecm
DTC Description
DTC DETECTION LOGIC
ECM back up system does not function properly.
EEPROM (built-in microcomputer) system internal ECM does not function properly...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Engine Does Not Start When Intelligent Key Is Inside of Vehicle (one Key)
Diagnosis Procedure Engine does not start when ignition switch is pressed. (One Intelligent Key has the symptom, other keys operate normally.)SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE SYMPTOM, OTHER KEYS OPERATE NORMALLY) Door lock operation (remote keyless entry) Door lock operation (request switch) or back door open operation (opener switch of back door panel) Engine started with push-button ignition switch operation (Intelligent Key is within the detection area of inside key antenna) Engine started with push-button ignition switch operation (registered Intelligent Key placed next to push-button ignition switch) OK OK No crank, No start No crank, No start DIAGNOSIS PROCEDURERefer to Diagnosis Procedure...
Nissan Murano (Z52) 2015-2024 Service Manual: Aeb Warning Lamp Is Blinking
Symptom Description The AEB warning lamp is blinking. Refer to Diagnosis Procedure.NOTE: When any of the following conditions, the AEB warning lamp blinks: The distance sensor area of the front of the Nissan Murano vehicle is covered with dirt or is obstructed The interior temperature of the vehicle is extremely high The windshield is dirty, frosted, fogged up, or damaged in front of the lane camera unit The lane camera unit or the lane camera unit bracket is not mounted properly Diagnosis Procedure CHECK THE WINDSHIELD Check if the windshield is dirty, frosted, fogged up, or damaged in front of the lane camera unit...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Tire rotation
- Rear bench seat adjustment
- Passenger compartment
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
