Nissan Murano: Dtc/circuit Diagnosis / Main Line Between 4wd and M&a Circuit

Nissan Murano (Z52) 2015-2024 Service Manual / Electrical & Power Control / Lan System :: Can / Dtc/circuit Diagnosis / Main Line Between 4wd and M&a Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector B101

    • Harness connector M84

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the harness connectors B101 and M84.

  2. Check the continuity between the harness connector terminals.

    Harness connector Continuity
    Connector No. Terminal No.
    B101 53J 75J Existed
    54J 76J Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the AWD control unit and the harness connector B101.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the harness connector of combination meter.

  2. Check the continuity between the harness connector and the combination meter harness connector.

Harness connector Combination meter harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M84 75J M23 53 Existed
76J 52 Existed

Is the inspection result normal?

YES>>

Check CAN system type decision again.

YES>>

Error was detected in the main line between the AWD control unit and the combination meter.

NO>>

Repair the main line between the harness connector M84 and the combination meter.

    Main Line Between Hvac and M&a Circuit

    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side)...

    Ecm Branch Line Circuit

    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the ECM for damage, bend and loose connection (unit side and connector side)...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: C1b01-55 Cam Aiming Incmp


    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition   C1B01-55 CAM AIMING INCMP (Camera aiming incomplete) Diagnosis condition When I-LI system is ON When driving the Nissan Murano vehicle Signal (terminal) — Threshold Camera aiming is not completed Diagnosis delay time 10 seconds or more POSSIBLE CAUSE Lane camera aiming is not adjusted Lane camera aiming adjustment has been interrupted Lane Camera Unit ADAS control unit FAIL-SAFEThe following systems are canceled: Lane Departure Warning (LDW) Intelligent Lane Intervention (I-LI) Blind Spot Warning (BSW) Rear Cross Traffic Alert (RCTA) Traffic Sign Recognition (TSR) Confirmation Procedure DTC CONFIRMATION PROCEDUREPERFORM DTC CONFIRMATION PROCEDURE CONSULT Start the engine...

    Nissan Murano (Z52) 2015-2024 Service Manual: Rear Wiper Arm


    Exploded View 1. Rear wiper arm cover 2. Seal 3. Rear wiper arm assembly 4. Rear wiper blade Removal and Installation REMOVALOperate the rear wiper arm into the auto stop position. Remove the rear wiper arm cover. Remove the rear wiper arm nut...

    Categories

    Front manual seat adjustment (if so equipped)

    Your vehicle seats can be adjusted manually. For additional information about adjusting the seats, refer to the steps outlined in this section.

    Forward and backward

    Nissan Murano. Front manual seat adjustment (if so equipped)

    read more

     
    Copyright © 2026 www.nimurano.com