Nissan Murano: Meter, Warning Lamp & Indicator :: Dtc/circuit Diagnosis / Fuel Level Sensor Signal Circuit

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Meter, Warning Lamp & Indicator :: Dtc/circuit Diagnosis / Fuel Level Sensor Signal Circuit

Component Function Check

COMBINATION METER INPUT SIGNAL

CONSULT

  1. Select “Data Monitor” mode of “METER/M&A”.

  2. Select “FUEL METER”.

  3. Compare the “FUEL METER” value and the fuel gauge reading of the combination meter. Fuel gauge and data monitor indications should be close.

    Combination meter Monitor item
    Fuel gauge

    FUEL METER [L]

    (Approx.)
    Full 70.6
    3/4 54.5
    1/2 38.3
    1/4 22.1
    Empty 8.6

Does the data monitor value approximately match the fuel gauge indication?

YES>>

Inspection End.

NO>>

Replace combination meter. Refer to Removal and Installation.

Diagnosis Procedure

CHECK HARNESS CONNECTOR

  1. Ignition switch OFF.

  2. Check combination meter and fuel level sensor unit and fuel pump (main) (fuel level sensor) terminals (meter-side and harness-side) for poor connection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace terminals or connectors.

CHECK FUEL LEVEL SENSOR CIRCUIT

  1. Disconnect combination meter harness connector and fuel level sensor unit and fuel pump (main) (fuel level sensor) harness connector.

  2. Check continuity between combination meter harness connector and fuel level sensor unit and fuel pump (main) (fuel level sensor) harness connector.

    Fuel level sensor unit and fuel pump (main) (fuel level sensor) Combination meter Continuity
    Connector Terminal Connector Terminal
    B72 5 M23 48 Yes

  3. Check continuity between fuel level sensor unit and fuel pump (main) (fuel level sensor) harness connector and ground.

    Fuel level sensor unit and fuel pump (main) (fuel level sensor) — Continuity
    Connector Terminal
    B72 5 Ground No

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK FUEL LEVEL SENSOR UNIT (MAIN-SUB) CIRCUIT

  1. Disconnect fuel level sensor unit (sub) harness connector.

  2. Check continuity between fuel level sensor unit and fuel pump (main) (fuel level sensor) harness connector and fuel level sensor unit (sub) harness connector.

    Fuel level sensor unit and fuel pump (main) (fuel level sensor) Fuel level sensor unit (sub) Continuity
    Connector Terminal Connector Terminal
    B72 2 B100 8 Yes

  3. Check continuity between fuel level sensor unit and fuel pump (main) (fuel level sensor) harness connector and ground.

    Fuel level sensor unit and fuel pump (main) (fuel level sensor) — Continuity
    Connector Terminal
    B72 2 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness or connector.

CHECK FUEL LEVEL SENSOR UNIT (SUB) CIRCUIT

  1. Check continuity between combination meter harness connector and fuel level sensor unit (sub) harness connector.

    Fuel level sensor unit (sub) Combination meter Continuity
    Connector Terminal Connector Terminal
    B100 7 M23 54 Yes

  2. Check continuity between fuel level sensor unit (sub) harness connector and ground.

    Fuel level sensor unit (sub) — Continuity
    Connector Terminal
    B100 7 Ground No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness or connector.

CHECK INSTALLATION CONDITION

Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the internal components in the fuel tank.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Install the fuel level sensor unit properly. Refer to Removal and Installation.

Component Inspection

CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (MAIN) (FUEL LEVEL SENSOR)

  1. Remove the fuel level sensor unit and fuel pump (main) (fuel level sensor). Refer to Removal and Installation.

  2. Check the resistance between fuel level sensor unit and fuel pump (main) (fuel level sensor) terminals.

    Fuel level sensor unit and fuel pump (main) (fuel level sensor) Condition

    Resistance (Ω)

    (Approx.)     		Height [mm (in)]
    Terminals
    2 5 Full* (A) 44 167 (6.6)
    Empty* (B) 137 19.8 (0.8)

    *: When float rod is in contact with stopper.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace fuel level sensor unit and fuel pump (main) (fuel level sensor). Refer to Removal and Installation.

CHECK FUEL LEVEL SENSOR UNIT (SUB)

  1. Remove the fuel level sensor unit (sub). Refer to Removal and Installation.

  2. Check the resistance between fuel level sensor unit (sub) terminals.

    Fuel level sensor unit (sub) Condition

    Resistance (Ω)

    (Approx.)     		Height [mm (in)]
    Terminals
    7 8 Full* (A) 7.0 187.9 (7.6)
    Empty* (B) 153 19.6 (0.8)

    *: When float rod is in contact with stopper.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace fuel level sensor unit (sub). Refer to Removal and Installation.

    Meter Control Switch Signal Circuit

    Diagnosis Procedure CHECK METER CONTROL SWITCH SIGNAL Ignition switch ON. Check voltage between the following terminals of the meter control switch harness connector...

    Washer Fluid Level Switch Circuit

    Diagnosis Procedure CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT Ignition switch OFF. Disconnect combination meter harness connector and washer fluid level switch harness connector...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis System (lane Camera Unit)


    CONSULT Function (LANE CAMERA UNIT) APPLICATION ITEMSCONSULT performs the following functions by communicating with the lane camera unit. Diagnosis mode Description Work support Performs the camera aiming. Self Diagnostic Result Displays the name of a malfunctioning system stored in the lane camera unit Data Monitor Displays lane camera unit input/output data in real time Ecu Identification Displays lane camera unit part number CAN Diag Support Monitor Displays a reception/transmission state of CAN communication Configuration The Nissan Murano vehicle specification that is written in lane camera unit can be displayed or stored The vehicle specification can be written when lane camera unit is replaced SELF DIAGNOSTIC RESULTRefer to DTC Index...

    Nissan Murano (Z52) 2015-2024 Service Manual: Engine Mechanical :: System Description. Noise, Vibration, and Harshness (nvh) Troubleshooting


    NVH Troubleshooting - Engine Noise 1. Camshaft bearing noise 2. Piston pin noise 3. Piston slap noise 4. Main bearing noise 5. Connecting rod bearing noise 6. Water pump noise 7. Timing chain and chain tensioner noise 8...

    Categories

    Driver and passenger supplemental knee air bag

    Nissan Murano. Driver and passenger supplemental knee air bag

    Driver’s side

    The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.

    Nissan Murano. Driver and passenger supplemental knee air bag

    Passenger’s side

    read more

     
    Copyright © 2026 www.nimurano.com