Nissan Murano: Action Test / Blind Spot Warning
Always perform the Blind Spot Warning system action test to check that the system operates normally after replacing the side radar LH/RH, or repairing any Blind Spot Warning system malfunction.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
-
Precautions: Refer to Blind Spot Warning/Rear Cross Traffic Alert (RCTA) System Service.
-
System description for Blind Spot Warning: Refer to System Description.
-
Normal operating condition: Refer to Description.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
-
Precautions: Refer to Blind Spot Warning/Rear Cross Traffic Alert (RCTA) System Service.
-
System description for Blind Spot Warning: Refer to System Description.
-
Normal operating condition: Refer to Description.
CHECK BSW SYSTEM SETTING
-
Start the engine.
-
Check that the BSW system setting can be enabled/disabled on the integral switch.
-
Turn OFF the ignition switch and wait for 5 seconds or more.
-
Check that the previous setting is saved when the engine starts again.
>>
GO TO 2.
BSW SYSTEM ACTION TEST
-
Enable the setting of the BSW system on the integral switch.
-
Check BSW operation according to the following table:
Nissan Murano Vehicle condition/ Driver's operation Action Nissan Murano Vehicle speed
(Approx.)Turn signal condition Status of Nissan Murano vehicle detection within detection area Indication on the
Blind Spot Warning indicatorIndication on the combination meter Indicator color Buzzer Less than approx.
18 MPH (29 km/h)— — OFF ON White OFF Approx.
20 MPH (32 km/h)
or more— Nissan Murano Vehicle is absent OFF ON White OFF OFF Nissan Murano Vehicle is detected ON ON White OFF ON
(Nissan Murano vehicle detected direction)Before turn signal operates
Vehicle is detectedBlink Blink Yellow (Blink) Short continuous beeps Nissan Murano Vehicle is detected after turn signal operates Blink Blink Yellow (Blink) OFF
>>
Inspection End.
Action Test
..
Rcta
Description
Always perform the RCTA system action test to check that the system operates normally after replacing the side radar LH/RH, or repairing any BSW/RCTA system malfunction...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Door Lock
Exploded View 1. Back door stay [(LH/RH) (without automatic back door)] 2. Spindle unit [(LH/RH) (with automatic back door)] 3. Back door touch sensor [(LH) (with automatic back door)] 4. Back door lock 5. Back door lock assembly (with automatic back door) 6...
Nissan Murano (Z52) 2015-2024 Service Manual: Hazard Switch Circuit
Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. Select “HAZARD SW” in “Data Monitor” mode of “BCM(FLASHER)”. While operating the hazard switch, check the monitor status. Monitor item Condition Monitor status HAZARD SW Hazard switch ON On OFF Off Is the inspection result normal? YES>> Hazard switch circuit is normal...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Rear bench seat adjustment
- Power Steering Fluid (PSF)
- GAS STATION INFORMATION
- New on site
- Most important about car
Vehicle security system
Your vehicle has two types of security systems:
Vehicle security system NISSAN Vehicle Immobilizer SystemThe vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
