Nissan Murano: Sonar System :: Basic Inspection / Additional Service When Replacing Sonar Control Unit

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Sonar System :: Basic Inspection / Additional Service When Replacing Sonar Control Unit

Description

BEFORE REPLACEMENT

When replacing sonar control unit, save or print current vehicle specification with CONSULT configuration before replacement.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing sonar control unit.

AFTER REPLACEMENT

CAUTION:

When replacing sonar control unit, you must perform “After Replace ECU” with CONSULT.

Complete the procedure of “After Replace ECU” in order.

If you set incorrect “After Replace ECU”, incidents might occur.

Configuration is different for each Nissan Murano vehicle model. Confirm configuration of each vehicle model.

Work Procedure

SAVING VEHICLE SPECIFICATION

CONSULT

Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current Nissan Murano vehicle specification.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing sonar control unit.

GO TO 2.

REPLACE SONAR CONTROL UNIT

Replace sonar control unit. Refer to Removal and Installation.

GO TO 3.

WRITING Nissan Murano Vehicle SPECIFICATION

CONSULT

Enter "Re/Programming, Configuration".
If “Before Replace ECU” operation was performed, an "Operation Log Selection" screen will automatically be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write Nissan Murano vehicle specification. Refer to Work Procedure.
If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configuration" to write Nissan Murano vehicle specification. Refer to Work Procedure.

GO TO 4.

OPERATION CHECK

Check that the operation of the sonar control unit is normal.

Work End.

Diagnosis and Repair Workflow

Work Flow OVERALL SEQUENCE Reference 1: Refer to CONSULT Function. Reference 2: Refer to DTC Index. Reference 3: Refer to Symptom Table. DETAILED FLOWINTERVIEW AND SYMPTOM CONFIRMATION Check the malfunction symptoms by performing the following items: Interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred)...

Configuration (sonar Control Unit)

Description Vehicle specification needs to be written with CONSULT. Configuration has three functions as follows: Function Description "Before Replace ECU" Reads the Nissan Murano vehicle configuration of current sonar control unit...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Open/closure Function

Diagnosis Procedure Back door auto closure function does not operate when back door opening and closing operations are performed.CHECK DTC WITH AUTOMATIC BACK DOOR CONTROL MODULE Check that DTC is not detected with automatic back door control module. Is the inspection result normal? YES>> GO TO 2...

Nissan Murano (Z52) 2015-2024 Service Manual: Engine Control System Symptoms

Symptom Table SYSTEM — BASIC ENGINE CONTROL SYSTEM SYMPTOM Reference page HARD/NO START/RESTART (EXCP. HA) ENGINE STALL HESITATION/SURGING/FLAT SPOT SPARK KNOCK/DETONATION LACK OF POWER/POOR ACCELERATION HIGH IDLE/LOW IDLE ROUGH IDLE/HUNTING IDLING VIBRATION SLOW/NO RETURN TO IDLE OVERHEATS/WATER TEMPERATURE HIGH EXCESSIVE FUEL CONSUMPTION EXCESSIVE OIL CONSUMPTION BATTERY DEAD (UNDER CHARGE) Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA Fuel Fuel pump circuit 1 1 2 3 2 2 2 3 2 Diagnosis Procedure Fuel pressure regulator system 3 3 4 4 4 4 4 4 4 4 Work Procedure Fuel injector circuit 1 1 2 3 2 2 2 2 Component Function Check Evaporative emission system 3 3 4 4 4 4 4 4 4 4 System Description Air Positive crankcase ventilation system 3 3 4 4 4 4 4 4 4 4 1 Positive Crankcase Ventilation (PCV) Incorrect idle speed adjustment 1 1 1 1 1 Work Procedure Electric throttle control actuator 1 1 2 3 3 2 2 2 2 2 2 DTC Description, DTC Description Ignition Incorrect ignition timing adjustment 3 3 1 1 1 1 1 1 Work Procedure Ignition circuit 1 1 2 2 2 2 2 2 Component Function Check Power supply and ground circuit 2 2 3 3 3 3 3 2 3 Diagnosis Procedure Mass air flow sensor circuit 1 1 2 2 2 2 2 2 DTC Description, DTC Description Engine coolant temperature sensor circuit 3 3 3 DTC Description, DTC Description Air fuel ratio (A/F) sensor 1 circuit DTC Description, DTC Description, DTC Description, DTC Description, DTC Description Throttle position sensor circuit 2 2 DTC Description, DTC Description, DTC Description, DTC Description, DTC Description Accelerator pedal position sensor circuit 3 2 1 DTC Description, DTC Description, DTC Description, DTC Description Knock sensor circuit 2 3 DTC Description Engine oil temperature sensor 4 2 3 DTC Description, DTC Description Crankshaft position sensor (POS) circuit 2 2 DTC Description Camshaft position sensor (PHASE) circuit 3 2 DTC Description Nissan Murano Vehicle speed signal circuit 2 3 3 3 DTC Description ECM 2 2 3 3 3 3 3 3 3 3 3 DTC Description, DTC Description Intake valve timing control solenoid valve circuit 3 2 1 3 2 2 3 3 DTC Description Intake valve timing intermediate lock control solenoid valve circuit DTC Description Exhaust valve timing control solenoid valve 3 2 1 3 2 2 3 3 DTC Description PNP signal circuit 3 3 3 3 3 DTC Description VIAS control solenoid valve 1 circuit 1 DTC Description VIAS control solenoid valve 2 circuit 1 DTC Description Refrigerant pressure sensor circuit 2 3 3 4 Component Function Check Electrical load signal circuit 3 Component Function Check Air conditioner circuit 2 2 3 3 3 3 3 3 3 3 2 Work Flow ABS actuator and electric unit (control unit) 4 Work Flow 1 - 6: The numbers refer to the order of inspection...