Nissan Murano: Dtc/circuit Diagnosis / U1000 Can Comm Circuit
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen item (Trouble diagnosis content) | DTC detected condition | |
|---|---|---|---|
| U1000 |
CAN COMM CIRCUIT (CAN communication circuit) |
Diagnosis condition |
|
| Signal (terminal) | CAN communication signal | ||
| Threshold | When CAN communication signal is not continuously transmitted or received. | ||
| Diagnosis delay time | 2 seconds or more | ||
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
| PAST DTC | CRNT DTC |
|---|---|
|
CAN communication system malfunction |
FAIL-SAFE
The following functions are suspended:
-
VDC function
-
TCS function
-
Brake assist function
-
Hill start assist function
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
CONSULT
-
Ignition switch OFF.
NOTE:
Wait at least 10 seconds after ignition switch OFF.
-
Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
-
Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “U1000” detected?
YES>>“CRNT” is displayed: Proceed to DTC Diagnosis Procedure.
YES>>“PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of “ABS”.)
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
Proceed to Trouble Diagnosis Flow Chart.
C1b68 Pump Motor
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen item
(Trouble diagnosis content) DTC detection condition
C1B68
PUMP MOTOR
(Pump motor)
Diagnosis condition
When ignition switch ON...
U1002 System Comm (can)
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen item
(Trouble diagnosis content) DTC detected condition
U1002
SYSTEM COMM (CAN)
(CAN system communication)
Diagnosis condition
When ignition switch ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P0715 Input Speed Sensor a
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0715 INPUT SPEED SENSOR A (Input/Turbine Speed Sensor “A” Circuit) Diagnosis condition When the following conditions are satisfied: TCM power supply voltage: More than 11 V After range change completion, it spends 2 seconds or more...
Nissan Murano (Z52) 2015-2024 Service Manual: B26fc Key Registration
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition B26FC KEY REGISTRATION (Key registration) Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Intelligent Key that does not match the Nissan Murano vehicle is registered Diagnosis delay time — POSSIBLE CAUSE Improper registration operation Intelligent Key BCM FAIL-SAFE— DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Perform initialization of BCM and reregistration of all Intelligent Keys...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- All-Wheel Drive (AWD) (if so equipped)
- Turning the AEB system on/off
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
