Nissan Murano: Dtc/circuit Diagnosis / P0327 Ks
DTC DETECTION LOGIC
-
An excessively low voltage from the sensor is sent to ECM.
-
An excessively high voltage from the sensor is sent to ECM.
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | |
| P0327 |
KNOCK SEN/CIRC-B1 (Knock sensor 1 circuit low bank 1) |
Diagnosis condition | Start engine and let it idle |
| Signal (terminal) | Voltage signal transmitted from knock sensor to ECM | ||
| Threshold | An excessively low voltage from the sensor is sent to ECM | ||
| Diagnosis delay time | — | ||
| P0328 |
KNOCK SEN/CIRC-B1 (Knock sensor 1 circuit high bank 1) |
Diagnosis condition | Start engine and let it idle |
| Signal (terminal) | Voltage signal transmitted from knock sensor to ECM | ||
| Threshold | An excessively high voltage from the sensor is sent to ECM. | ||
| Diagnosis delay time | — | ||
| P0332 |
KNOCK SEN/CIRC-B2 (Knock sensor 2 circuit low bank 2) |
Diagnosis condition | Start engine and let it idle |
| Signal (terminal) | Voltage signal transmitted from knock sensor to ECM | ||
| Threshold | An excessively low voltage from the sensor is sent to ECM | ||
| Diagnosis delay time | — | ||
| P0333 |
KNOCK SEN/CIRC-B1 (Knock sensor 2 circuit high bank 2) |
Diagnosis condition | Start engine and let it idle |
| Signal (terminal) | Voltage signal transmitted from knock sensor to ECM | ||
| Threshold | An excessively high voltage from the sensor is sent to ECM. | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
P0327
-
Harness or connectors (The sensor circuit is open or shorted.)
-
Knock sensor
P0328
-
Harness or connectors (The sensor circuit is open or shorted.)
-
Knock sensor
P0332
-
Harness or connectors (The sensor circuit is open or shorted.)
-
Knock sensor
P0333
-
Harness or connectors (The sensor circuit is open or shorted.)
-
Knock sensor
FAIL-SAFE
Not applicable
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start engine and run it for at least 5 seconds at idle speed.
-
Check 1st trip DTC.
Is 1st trip DTC detected?
YES>>Proceed to Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: INSPECTION END
CHECK KNOCK SENSOR GROUND CIRCUIT
-
Disconnect knock sensor harness connector and ECM harness connector.
-
Check the continuity between knock sensor harness connector and ECM harness connector.
DTC Knock sensor ECM Continuity Bank Connector Terminal Connector Terminal P0327, P0328 1 F202 2 F78 4 Existed P0332, P0333 2 F203 2 -
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair open circuit, short to ground or short to power in harness or connectors.
CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT
-
Check the continuity between knock sensor harness connector and ECM harness connector.
DTC Knock sensor ECM Continuity Bank Connector Terminal Connector Terminal P0327, P0328 1 F202 1 F78 5 Existed P0332, P0333 2 F203 1 9 -
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair open circuit, short to ground or short to power in harness or connectors.
CHECK KNOCK SENSOR
Check knock sensor. Refer to Component Inspection.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace malfunctioning knock sensor. Refer to Exploded View.
CHECK KNOCK SENSOR
-
Turn ignition switch OFF.
-
Disconnect knock sensor harness connector.
-
Check resistance between knock sensor terminal as per the following.
NOTE:
It is necessary to use an ohmmeter which can measure more than 10 MΩ.
Knock sensor Resistance + - Terminals 1 2 Approx. 532 - 588 kΩ [at 20°C (68°F)] CAUTION:
Never use any knock sensors that have been dropped or physically damaged. Use only new ones.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace malfunctioning knock sensor. Refer to Exploded View.
P0326 Knock Sensor
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detected condition
P0326
KNOCK SENSOR 1 B1
(Knock/Combustion Vibration Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor)
Diagnosis condition
During fuel cut after engine warm-up
Signal
Knock sensor
Threshold
When the ECM detects knocking during engine running more than the threshold value
Diagnosis delay time
5 seconds
POSSIBLE CAUSEHarness or connectors(The knock sensor circuit is open or shorted...
P0335 Ckp Sensor (pos)
DTC Description
DTC DETECTION LOGIC
The crankshaft position sensor (POS) signal is not detected by the ECM during the first few seconds of engine cranking...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P2813 Select Solenoid
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2813 SELECT SOLENOID (Select solenoid) 1 Diagnosis condition When all of the following conditions are satisfied: DTC other than the applicable DTC is not detected...
Nissan Murano (Z52) 2015-2024 Service Manual: B26f1 Ign Relay Off
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition B26F1 IGN RELAY OFF (Ignition relay off) Diagnosis condition When ignition switch ON. Signal (terminal) IPDM E/R ignition output 1 (Terminal 70) Threshold Less than 8...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Indicator lights
- Warning lights
- Intelligent Forward Collision Warning (I-FCW)
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
