Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / Main Power Window and Door Mirror Switch. Select Switch
DATA MONITOR
CONSULT
-
Select “MIR CHNG SW-R” and “MIR CHNG SW-L” in “Data Monitor” mode of “AUTO DRIVE POS.”.
-
Check that the function operates normally according to the following conditions:
Monitor item Condition Status MIR CHNG SW-R Mirror switch (right) Operate ON Release OFF MIR CHNG SW-L Mirror switch (left) Operate ON Release OFF
Is the inspection result normal?
YES>>Inspection End.
NO>>Perform diagnosis procedure. Refer to Diagnosis Procedure.
CHECK SELECT SWITCH SIGNAL
-
Ignition switch ON.
-
Check voltage between automatic drive positioner control unit connector and ground.
(+) (-) Select switch condition Voltage
(Approx.)Automatic drive positioner control unit Connector Terminal M33 2 Ground RIGHT 0V Other than above 5V 14 LEFT 0V Other than above 5V
Is the inspection result normal?
YES>>GO TO 5.
NO>>GO TO 2.
CHECK HARNESS CONTINUITY
-
Ignition switch OFF.
-
Disconnect automatic drive positioner control unit and door mirror remote control switch.
-
Check continuity between automatic drive positioner control unit connector and door mirror remote control switch connector.
Automatic drive positioner control unit Door mirror remote control switch Continuity Connector Terminal Connector Terminal M33 2 D22 3 Yes 14 4 -
Check continuity between automatic drive positioner control unit connector and ground.
Automatic drive positioner control unit Ground Continuity Connector Terminal M33 2 No 14
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connector and ground.
| Door mirror remote control switch | Ground | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| D22 | 15 | Yes | |
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace harness.
CHECK SELECT SWITCH
Check select switch.
Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace automatic drive positioner control unit. Refer to Removal and Installation.
NO>>Replace door mirror remote control switch. Refer to Removal and Installation.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to Intermittent Incident.
Is the inspection result normal?
YES>>Replace automatic drive positioner control unit. Refer to Removal and Installation.
NO>>Repair or replace the malfunctioning parts.
CHECK SELECT SWITCH
-
Ignition switch OFF.
-
Disconnect door mirror remote control switch.
-
Check continuity between door mirror remote control switch terminals.
Door mirror remote control switch Select switch condition Continuity Terminal 4 15 LEFT Yes Other than above No 3 RIGHT Yes Other than above No
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace door mirror remote control switch. Refer to Removal and Installation.
Seat Memory Switch
Component Function Check
DATA MONITOR
CONSULT
Select “MEMORY SW 1”, “MEMORY SW 2” and “SET SW” in “Data Monitor” mode of “AUTO DRIVE POS...
Power Seat Switch Lh Ground Circuit
Diagnosis Procedure
CHECK POWER SEAT SWITCH LH GROUND CIRCUIT
Ignition switch OFF.
Disconnect power seat switch LH.
Check continuity between power seat switch LH connector and ground...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: C1609 Can Vhcl Speed
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1609 CAN VHCL SPEED (CAN Nissan Murano vehicle speed signal) Diagnosis condition When engine is ON Signal (terminal) Nissan Murano Vehicle speed signal Threshold ABS actuator and electric unit (control unit) input signal error is detected...
Nissan Murano (Z52) 2015-2024 Service Manual: Throttle Control
System Description SYSTEM DIAGRAM*: ECM determines the start signal status by the signals of engine speed and battery voltage.SYSTEM DESCRIPTIONECM calculates the value of signal transmitted from the accelerator pedal and activates the throttle valve by transmitting a control signal to the electric throttle control actuator...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- High Beam Assist (if so equipped)
- Memory storage function (key-link)
- GAS STATION INFORMATION
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
