Nissan Murano: Driver Controls / Defogger :: Basic Inspection. Diagnosis and Repair Work Flow

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Controls / Defogger :: Basic Inspection. Diagnosis and Repair Work Flow

Work Flow

OVERALL SEQUENCE

DETAILED FLOW

GET INFORMATION FOR SYMPTOM

Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred).

>>

GO TO 2.

CHECK DTC

CONSULT

  1. Check DTC.

  2. Perform the following procedure if DTC is displayed:

    • Record DTC and freeze frame data. (Print them out.)

    • Erase DTC.

    • Study the relationship between the cause detected by DTC and the symptom described by the customer.

  3. Check related service bulletins for information.

Is any symptom described and any DTC detected?

Symptom is described, DTC is displayed>>

GO TO 3.

Symptom is described, DTC is not displayed>>

GO TO 4.

Symptom is not described, DTC is displayed>>

GO TO 5.

CONFIRM THE SYMPTOM

CONSULT

Confirm the symptom described by the customer.

Select "Data Monitor" mode of "BCM(REAR DEFOGGER)" and check real-time diagnosis results.

Verify relation between the symptom and the condition when the symptom is detected.

>>

GO TO 5.

CONFIRM THE SYMPTOM

CONSULT

Confirm the symptom described by the customer.

Select "Data Monitor" mode of "BCM(REAR DEFOGGER)" and check real-time diagnosis results.

Verify relation between the symptom and the condition when the symptom is detected.

>>

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.

At this time, always connect CONSULT to the Nissan Murano vehicle, and check diagnostic results in real time.

If two or more DTCs are detected, refer to DTC Inspection Priority Chart and determine trouble diagnosis order.

NOTE:

  • Freeze frame data is useful if the DTC is not detected.

  • Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during this check.

    If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure.

Is DTC detected?

YES>>

GO TO 6.

NO>>

Refer to Intermittent Incident.

DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Detect malfunctioning system according to System Description based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.

>>

GO TO 7.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

CONSULT

Inspect according to Diagnostic Procedure of the system.

NOTE:

The Diagnostic Procedure described is based on open circuit inspection. A short circuit inspection is also required for the circuit check in the Diagnostic Procedure.

Is malfunctioning part detected?

YES>>

GO TO 8.

NO>>

Check voltage of related BCM terminals.

REPAIR OR REPLACE THE MALFUNCTIONING PART

CONSULT

  1. Repair or replace the malfunctioning part.

  2. Reconnect parts or connectors disconnected during Diagnostic Procedure after repair and replacement.

  3. Check DTC. If DTC is displayed, erase it.

>>

GO TO 9.

FINAL CHECK

When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check again, and then check that the malfunction has been repaired.

When symptom was described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.

Does the symptom reappear?

YES (DTC is detected)>>

GO TO 7.

YES (Symptom remains)>>

GO TO 6.

NO>>

Inspection End.

    Defogger :: Ecu Diagnosis Information. Bcm, A/c Auto Amp.

    List of ECU Reference ECU Reference BCM Values on the Diagnosis Tool Reference Value Fail Safe DTC Inspection Priority Chart DTC Index A/C auto amp...

    Defogger :: Dtc/circuit Diagnosis

    ..

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: B2724 Sonar Control Unit


    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2724–23 SONAR CONTROL UNIT (Sonar control unit) — Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (under voltage) Diagnosis delay time — B2724–24 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (over voltage) Diagnosis delay time — B2724–44 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (RAM failure) Diagnosis delay time — B2724–45 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (ROM failure) Diagnosis delay time — B2724–46 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (EEPROM failure) Diagnosis delay time — B2724–48 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (internal software execution failure) Diagnosis delay time — B2724–49 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (basic chip set failure) Diagnosis delay time — B2724–55 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (not configured) Diagnosis delay time — B2724–86 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (SPI comm failure) Diagnosis delay time — B2724–87 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (high side switch failure) Diagnosis delay time — POSSIBLE CAUSE Charging system malfunction Sonar control unit power supply or ground circuit Sonar control unit configuration Sonar control unit FAIL-SAFE Off indicator blinks periodically (500ms ON, 500ms OFF)...

    Nissan Murano (Z52) 2015-2024 Service Manual: U1000 Can Comm Circuit


    DTC Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Murano vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Murano vehicle, and each control unit shares information and links with other control units during operation (not independent)...

    Categories

    Driver and passenger supplemental knee air bag

    Nissan Murano. Driver and passenger supplemental knee air bag

    Driver’s side

    The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.

    Nissan Murano. Driver and passenger supplemental knee air bag

    Passenger’s side

    read more

     
    Copyright © 2026 www.nimurano.com