Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / B2128 Uart Comm
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC Detection Condition | |
|---|---|---|---|
| B2128 |
UART COMM (Universal asynchronous receiver transmitter communication) |
Diagnosis condition | — |
| Signal (terminal) | — | ||
| Threshold | Communication between driver seat control unit and automatic drive positioner control unit is interrupted. | ||
| Diagnosis delay time | A period of time. | ||
POSSIBLE CAUSE
-
UART communication line
(UART communication line is open or shorted)
-
Driver seat control unit
-
Automatic drive positioner control unit
FAIL-SAFE
Only manual functions, except door mirror, operate normally.
SELF-DIAGNOSIS WITH AUTOMATIC DRIVE POSITIONER CONTROL UNIT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.
-
Check DTC.
Is the DTC detected?
YES>>Perform diagnosis procedure. Refer to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.
-
Erase the DTC.
-
Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.
Is the DTC displayed again?
YES>>GO TO 2.
NO>>Check intermittent incident. Refer to Intermittent Incident.
CHECK UART COMMUNICATION LINE CONTINUITY
-
Ignition switch OFF.
-
Disconnect driver seat control unit and automatic drive positioner control unit.
-
Check continuity between driver seat control unit harness connector and automatic drive positioner control unit harness connector.
Driver seat control unit connector Automatic drive positioner control unit connector Continuity Connector Terminal Connector Terminal B209 15 M33 8 Yes -
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit Ground Continuity Connector Terminal B209 15 No
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Repair or replace harness.
B2112 Seat Slide
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
B2112
SEAT SLIDE
(Seat slide)
Diagnosis condition
When ignition switch ON...
B2130 Eeprom
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
B2130
EEPROM
(EEPROM malfunction)
Diagnosis condition
—
Signal (terminal)
—
Threshold
Driver seat control unit detected a CPU malfunction...
Other information:
Nissan Murano (Z52) 2015-2024 Owners Manual: Heater and Air Conditioner (automatic)
Temperature control dial (driver’s side)/AUTO button ON-OFF button Display screen MODE (manual air flow control) button Temperature control dial (passenger’s side)/DUAL button Fresh air intake button Air recirculation button A/C (air conditioner) button fan speed control buttons REAR window and outside mirror (if so equipped) defroster switch FRONT (defroster) button WARNING The air conditioner cooling function operates only when the engine is running...
Nissan Murano (Z52) 2015-2024 Service Manual: Power Supply and Ground Circuit (side Radar Lh)
Work Procedure CHECK FUSES Check that the following fuse is not blown: Signal name Fuse No. Ignition power supply 29(10 A) Is the fuse blown? YES>> Replace the blown fuse after repairing the affected circuit. NO>> GO TO 2. CHECK POWER SUPPLY CIRCUIT Turn ignition switch OFF...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Rear bench seat adjustment
- Vehicle Dynamic Control (VDC) OFF switch
- How to enable/disable the LDW system
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
