Nissan Murano: Dtc/circuit Diagnosis / Sensor Power Supply2 Circuit

Nissan Murano (Z52) 2015-2024 Service Manual / Engine / Engine Control System :: Vq35de / Dtc/circuit Diagnosis / Sensor Power Supply2 Circuit

Diagnosis Procedure

ECM supplies a voltage of 5 V to some of the sensors systematically divided into 2 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the short-circuited sensor.

Sensor power supply 1

  • Accelerator pedal position (APP) sensor 1

  • Crankshaft position (CKP) sensor (POS)

  • Exhaust valve timing (EVT) control position sensor

  • Mass air flow (MAF) sensor

  • Throttle position (TP) sensor

NOTE:

If sensor power supply 1 circuit is malfunctioning, DTC P0643 is displayed.

Sensor power supply 2

  • Accelerator pedal position (APP) sensor 2

  • Camshaft position (CMP) sensor (PHASE)

  • Engine oil pressure (EOP) sensor

  • Refrigerant pressure sensor

CHECK SENSOR POWER SUPPLY 2

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connectors

  3. Turn ignition switch ON.

  4. Check the voltage between ECM harness connector and ground.

    + −

    Voltage

    (Approx.)
    ECM
    Connector Terminal
    E32 142 Ground 5 V
    F78 18
    F79 92

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 2.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect following sensors harness connector.

  3. Check harness for short to power and short to ground, between the following terminals.

ECM Sensor
Connector Terminal Name Connector Terminal
E32 142 APP sensor 2 E31 5
F78 18 Refrigerant pressure sensor E244 1
EOP sensor F87 3
F79 92 CMP sensor (PHASE) (bank 1) F77 1
CMP sensor (PHASE) (bank 2) F60 1

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK COMPONENTS

Check the following.

  • Accelerator pedal position (APP) sensor 2 (Refer to Component Inspection.)

  • Camshaft position sensor (PHASE) (bank 1) (Refer to Component Inspection.)

  • Camshaft position sensor (PHASE) (bank 2) (Refer to Component Inspection.)

  • Engine oil pressure (EOP) sensor (Refer to Component Inspection.)

  • Refrigerant pressure sensor (Refer to Diagnosis Procedure.)

Is the inspection result normal?

YES>>

Perform Intermittent Incident.

NO>>

Replace malfunctioning component.

    Refrigerant Pressure Sensor

    Component Function Check CHECK REFRIGERANT PRESSURE SENSOR FUNCTION Start engine and warm it up to normal operating temperature. Turn A/C switch and blower fan switch ON...

    Variable Induction Air System

    Component Function Check CHECK OVERALL FUNCTION-I With CONSULT Start engine and warm it up to the normal operating temperature. Perform “VIAS S/V-1” in “ACTIVE TEST” mode with CONSULT...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: U1010-49 Control Unit (can)


    DTC Description CAN controller controls the communication of CAN communication signal and the error detection.DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition   U1010-49 CONTROL UNIT (CAN) [Control unit (CAN)] Diagnosis condition When engine is running When MAIN switch of ICC system is ON Signal (terminal) — Threshold If ADAS control unit detects malfunction by CAN controller initial diagnosis Diagnosis delay time 1 second or less POSSIBLE CAUSEADAS control unitFAIL-SAFEThe following systems are canceled: Automatic Emergency Braking (AEB) with pedestrian detection Automatic Emergency Braking (AEB) Intelligent Forward Collision Warning (I-FCW) Lane Departure Warning (LDW) Intelligent Lane Intervention (I-LI) Blind Spot Warning (BSW) Rear Cross Traffic Alert (RCTA) Rear Automatic Braking (RAB) Traffic Sign Recognition (TSR) Intelligent Drive Alertness (I-DA) Confirmation Procedure DTC CONFIRMATION PROCEDUREPERFORM DTC CONFIRMATION PROCEDURE CONSULT Start the engine...

    Nissan Murano (Z52) 2015-2024 Owners Manual: How to change the set distance to the vehicle ahead


    The distance to the vehicle ahead can be selected at any time depending on the traffic conditions. Each time the distance switch is pushed, the set distance will change to long, middle, short and back to long again, in that sequence. Distance Approximate distance at 60 mph (100 km/h) [ft (m)] Long 200 (60) Middle 150 (45) Short 90 (30) The distance to the vehicle ahead will change according to the vehicle speed...

    Categories

    read more

     
    Copyright © 2026 www.nimurano.com