Nissan Murano: Basic Inspection / How to Erase Permanent Dtc
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same malfunction is not detected after performing the driving pattern for MIL shutoff three times in a raw.
| *1: | When the same malfunction is detected in two consecutive trips, MIL will illuminate. | *2: | MIL will turn off after Nissan Murano vehicle is driven 3 times (driving pattern B) without any malfunctions. |
When a DTC is not stored in ECM
The erasing method depends on a permanent DTC stored in ECM. Refer to the following table.
NOTE:
If the applicable permanent DTC includes multiple groups, perform the procedure of Group B first. If the permanent DTC is not erased, perform the procedure of Group A.
×: Applicable —: Not applicable
| Group* | Perform “DTC CONFIRMATION PROCEDURE” for applicable DTCs. | Driving pattern | Reference | |
|---|---|---|---|---|
| B | D | |||
| A | × | — | — | Work Procedure (Group A) |
| B | — | × | × | Work Procedure (Group B) |
*: For group, refer to DTC Index.
PERMANENT DTC ITEM
For permanent DTC items, MIL turns ON. Refer to DTC Index.
PERMANENT DTC SERVICE PROCEDURE
| *1: | When the same malfunction is detected in two consecutive trips, MIL will illuminate. |
CHECK DTC
Check DTC.
Is any DTC detected?
YES>>Repair malfunction(s) and erase DTC. Refer to CONSULT Function.
NO>>GO TO 2.
CHECK PERMANENT DTC
With CONSULT
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select Service $0A with GST.
Is any permanent DTC detected?
YES>>GO TO 3.
NO>>END
PERFORM DTC CONFIRMATION PROCEDURE
Perform “DTC CONFIRMATION PROCEDURE” for DTCs which are the same as permanent DTCs stored in ECM. Refer to DTC Index.
>>
GO TO 4.
CHECK PERMANENT DTC
With CONSULT
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select Service $0A with GST.
Is any permanent DTC detected?
YES>>GO TO 1.
NO>>END
| *1: | When the same malfunction is detected in two consecutive trips, MIL will illuminate. | *2: | After experiencing driving pattern B and D, permanent DTC is erased. | *3: | Indication does not change unless the ignition switch is turned from ON to OFF twice even after experiencing driving pattern B or D. |
NOTE:
Drive the vehicle according to only driving patterns indicating “INCMP” in driving patterns B and D on the “PERMANENT DTC STATUS” screen.
CHECK DTC
Check DTC.
Is any DTC detected?
YES>>Repair malfunction(s) and erase DTC. Refer to CONSULT Function.
NO>>GO TO 2.
CHECK PERMANENT DTC
With CONSULT
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select Service $0A with GST.
Is any permanent DTC detected?
YES>>GO TO 3.
NO>>END
DRIVE DRIVING PATTERN B
CAUTION:
-
Always drive at a safe speed.
-
Never erase self-diagnosis results.
-
If self-diagnosis results are erased during the trip of driving pattern B or D, the counter of driving pattern B and D is reset.
With CONSULT
-
Start engine and warm it up to normal operating temperature.
-
Use “PERMANENT DTC WORK SUPPORT” mode with CONSULT to drive the Nissan Murano vehicle according to driving pattern B. Refer to CONSULT Function, Driving Pattern.
With GST
-
Start engine and warm it up to normal operating temperature.
-
Drive the Nissan Murano vehicle according to driving pattern B. Refer to Driving Pattern.
>>
GO TO 4.
CHECK PERMANENT DTC
With CONSULT
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select Service $0A with GST.
Is any permanent DTC detected?
YES>>GO TO 5.
NO>>END
DRIVE DRIVING PATTERN D
CAUTION:
-
Always drive at a safe speed.
-
Never erase self-diagnosis results.
-
If self-diagnosis results are erased during the trip of driving pattern B or D, the counter of driving pattern B and D is reset.
-
Drive the Nissan Murano vehicle according to driving pattern D. Refer to Driving Pattern.
>>
GO TO 6.
CHECK PERMANENT DTC
With CONSULT
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Select Service $0A with GST.
Is any permanent DTC detected?
YES>>GO TO 1.
NO>>END
How to Set Srt Code
Description
OUTLINEIn order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least once. Each diagnosis may require actual driving for a long period of time under various conditions...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Maintenance :: Preparation. Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-48891) Spark plug socket Removing and installing spark plug — (J-51771) Cooling system pressure test kit — (J-51771-1) Main body — (J-51771-4) Small adapter — (J-51771-5) Pump with quick release — (J-51771-9) Radiator cap assembly with quick coupler Checking cooling system and radiator cap KV991J0070 (J-45695-A) Coolant Refill Tool Refilling engine cooling system (J-43926) Refrigerant dye leak detection kit Kit includes: UV lamp and UV safety goggles Refrigerant dye injector Fluorescent leak detection dye (box of 24, 1/4 ounce bottles) Refrigerant dye cleaner Power supply: DC 12V (battery terminal) (J-52990) Fluorescent Oil Dye (TIFZX) Electronic Refrigerant Leak Detector Detects refrigerant leaks KV311039S0 ( — ) Charging pipe set KV31103920* ( — ) O-ring CVT fluid changing and adjustment ( — ) (J-52584) CVT stand pipe adapter kit CVT fluid changing and adjustment (—) (J-51155) CVT8 fluid level quick check gauge Checking CVT fluid level ( — ) (J-52611) CVT charge pipe cap release tool Removing CVT charge pipe cap Commercial Service Tool (TechMate No...
Nissan Murano (Z52) 2015-2024 Service Manual: Power Steering Oil Pump
Exploded View 1. Power steering reservoir cap 2. Power steering oil pump 3. Low-pressure piping 4. High-pressure piping Front Removal and Installation WARNING: Power steering pump outer shell will be hot while running and after driving...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Jacking up vehicle and removing the damaged tire
- Fuel recommendation
- How to enable/disable the LDW system
- New on site
- Most important about car
Seatback pockets
Theremaybe one or two seatback pockets located on the back of the driver and passenger seats. The pockets can be used to store maps.
WARNING
