Nissan Murano: System / Front Wiper and Washer System

System Description

SYSTEM DIAGRAM

Signal transmission function list

OUTLINE

The front wiper is controlled by each function of BCM and IPDM E/R.

Control by BCM:

• Combination switch reading function

• Front wiper control function

Control by IPDM E/R:

• Front wiper control function

• Relay control function

Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For details of low washer fluid warning, refer to System Description.

FRONT WIPER BASIC OPERATION

• BCM detects the combination switch (wiper and washer switch) condition by the combination switch reading function.

• BCM transmits the front wiper request signal to IPDM E/R via CAN communication depending on each operating condition of the front wiper.

• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.

FRONT WIPER LO OPERATION

• BCM transmits the front wiper request signal (LO) to IPDM E/R via CAN communication according to the front wiper LO operating condition.

  Front wiper LO operating condition:

  • Ignition switch ON

  • Front wiper switch LO or front wiper switch MIST (while pressing)

• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).

FRONT WIPER HI OPERATION

• BCM transmits the front wiper request signal (HI) to IPDM E/R via CAN communication according to the front wiper HI operating condition.

  Front wiper HI operating condition:

  • Ignition switch ON

  • Front wiper switch HI

• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper request signal (HI).

FRONT WIPER INT OPERATION

• BCM transmits the front wiper request signal (INT) to IPDM E/R via CAN communication depending on the front wiper INT operating condition and intermittent operation delay interval according to the wiper intermittent dial position.

  Front wiper INT operating condition:

  • Ignition switch ON

  • Front wiper switch INT

• IPDM E/R turns ON the integrated front wiper relay so that the front wiper is operated only once according to the front wiper request signal (INT).

• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop position signal received from IPDM E/R via CAN communication.

• BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval.

  

NOTE:

Factory setting of the front wiper intermittent operation is without speed dependant function. Front wiper speed dependant function can be set in the Nissan Murano vehicle settings of the Vehicle Information Display.

*: When without vehicle speed setting

FRONT WIPER AUTO STOP OPERATION

• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.

• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper motor position (stop position/except stop position).

• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper motor returns to the stop position.

NOTE:

• BCM stops the transmitting of the front wiper request signal when the ignition switch is placed OFF.

• IPDM E/R turns the front wiper relay OFF when the ignition switch is placed OFF.

FRONT WIPER OPERATION LINKED WITH WASHER

• BCM transmits the front wiper request signal (LO) to IPDM E/R via CAN communication according to the washer linked operating condition of the front wiper.

• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately two times when the front washer switch OFF is detected.

  Washer linked operating condition of front wiper:

  • Ignition switch ON

  • Front washer switch ON (0.4 seconds or more)

• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).

• The front and rear washer motor is supplied power and ground from the combination switch (wiper and washer switch) with the front washer switch ON.

FRONT WIPER FAIL-SAFE OPERATION

IPDM E/R performs the fail-safe function when the front wiper stop position circuit is malfunctioning.